n?3 ^%0h^^ BLM..trary ^ D-553A, Building 50 < ^cf y Denver Federal Center P. 0. Box 25047 Denver, CO 80225-0047 NEW YORK BUTTE G-E-M RESOURCES AREA (GRA NO. CA-10) TECHNICAL REPORT (WSAs CA 010-055 and 010-056) Contract YA-553-RFP2-1054 Prepared By Great Basin GEM Joint Venture 251 Ralston Street Reno, Nevada 89503 For Bureau of Land Management Denver Service Center Building 50, Mailroora Denver Federal Center Denver, Colorado 80225 Final Report April 22, 1983 TABLE OF CONTENTS Page EXECUTIVE SUMMARY 1 I . INTRODUCTION 3 II. GEOLOGY 10 1 . PHYSIOGRAPHY 10 2. ROCK UNITS 10 3 . STRUCTURAL GEOLOGY AND TECTONICS H 4. PALEONTOLOGY 12 5 . HISTORICAL GEOLOGY 12 III . ENERGY AND MINERAL RESOURCES 14 A. METALLIC MINERAL RESOURCES 14 1 . Known Mineral Deposits 14 2. Known Prospects, Mineral Occurrences and Mineralized Areas 18 3 . Mining Claims 19 4. Mineral Deposit Types 19 5. Mineral Economics 20 B. NONMETALLIC MINERAL RESOURCES 22 1 . Known Mineral Deposits 22 2. Known Prospects, Mineral Occurrences and Mineralized Areas 23 3. Mining Claims, Leases and Material Sites 23 4. Mineral Deposit Types 23 5. Mineral Economics 24 Table of Contents cont . Page C . ENERGY RESOURCES 2 5 Uranium and Thorium Resources 25 1. Known Mineral Deposits 25 2. Known Prospects, Mineral Occurrences and Mineralized Areas 25 3 . Mining Claims 25 4. Mineral Deposit Types 26 5 . Mineral Economics 2 6 Oil and Gas Resources 27 Geothermal Resources 27 1 . Known Geothermal Deposits 27 2. Known Prospects, Geothermal Occurrences, and Geothermal Areas 27 3. Geothermal Leases 28 4. Geothermal Deposit Types 28 5. Geothermal Economics 28 D. OTHER GEOLOGICAL RESOURCES 29 E. STRATEGIC AND CRITICAL MINERALS AND METALS 29 IV. LAND CLASSIFICATION FOR G-E-M RESOURCES POTENTIAL ... 30 1 . LOCATABLE RESOURCES 31 a . Metallic Minerals 31 b . Uranium and Thorium 33 c. Nonmetallic Minerals 34 • Table of Contents cont. % Page 2 . LEASABLE RESOURCES 3 5 a. Oil and Gas 35 b . Geo thermal 35 c. Sodium and Potassium 36 3 . SALEABLE RESOURCES 3 6 V. RECOMMENDATIONS FOR ADDITIONAL WORK 37 VI . REFERENCES AND SELECTED BIBLIOGRAPHY 38 • • Table of Contents cont. Page LIST OF ILLUSTRATIONS Figure 1 Index Map of Region 3 showing the Location of the GRA 5 Figure 2 Topographic map of GRA, scale 1:250,000 6 Figure 3 Geologic map of GRA, scale 1:250,000 7 ATTACHMENTS (At End of Report) CLAIM AND LEASE MAPS Patented/Unpatented Geothermal % MINERAL OCCURRENCE AND LAND CLASSIFICATION MAPS (Attached) Metallic Minerals Uranium and Thorium Nonmetallic Minerals Geothermal LEVEL OF CONFIDENCE SCHEME CLASSIFICATION SCHEME MAJOR STRATIGRAPHIC AND TIME DIVISIONS IN USE BY THE U.S. GEOLOGICAL SURVEY v EXECUTIVE SUMMARY The New York Butte GRA covers much of the southern Inyo Mountains, east of Lone Pine in Inyo County, California. There are two WSAs in the GRA: CA 010-055 and CA 010-056. The rocks of the GRA are mostly Paleozoic sediments (200 to 500 million years old) that have been intruded by small quartz monzonite stocks (about 200 million years old) in the WSAs although to the north there are large intrusive bodies of similar composition. All mineralization in the GRA is considered to be related to these intrusive bodies. The principal mining district within the GRA, Cerro Gordo, is just east of the south end of WSA CA 010-055; it produced silver, lead and zinc, mostly in the late 1800s. The Bonham talc deposits, which were highly productive in the past, also lie just east of WSA CA 010-055. Along the west boundary of WSA CA 010-055, outside it, substantial production of limestone and dolomite has been made in the past; none of the quarries are operating presently. The Burgess mine in WSA CA 010-056 has produced an unknown amount of gold, and the Monte Carlo mine in the same WSA has produced some silver and lead. Several smaller mines in both WSAs have probably had limited production, mostly of silver and lead. Silver and lead are both strategic metals. During a two-day field verification, by helicopter, most of the mines and prospects in the WSAs were examined and sampled; assay data from the samples is not yet available. Three patented claims may be within WSA CA 010-055; they plot about on the WSA boundary. The southern half of WSA CA 010-055 is apparently almost completely covered with unpatented claims. There are many unpatented claims in WSA CA 010-056, mostly near the west edge but some scattered within the main body of the WSA, and a few in the vicinity of the Burgess mine. There are no oil and gas or sodium and potassium leases in the WSAs. There are geothermal leases a short distance west of the WSAs but none within them. There are no known material sites in the WSAs. WSA CA 010-055 has two very small areas classified as highly favorable for metallic minerals with moderate confidence, and two larger areas classified as having low favorability for metals with low confidence; most of the WSA is classified as having no known favorability for metallic minerals with a low level of confidence. Virtually all of the WSA has moderate favorability for uranium with a moderate level of confidence; it has very low favorability for thorium with a low level of confidence. About one-fourth of the WSA has moderate favorability for lime or cement production, with a moderate level of confidence, while the remainder has low favorability for nonmetallic minerals with a low level of confidence. There is no known favorability for oil and gas, coal, oil shale, tar sands or sodium and potassium. The west edge of the WSA has high favorability with high confidence for geothermal resources, while the remainder of the WSA has low favorability with a low level of confidence. WSA CA 010-056 has two areas of several square miles with high favorability for metallic minerals and high to moderate confidence, and another very small area with high favorability and moderate confidence. Another area of several square miles has moderate favorability for metals with high confidence. Three areas totalling about one-third of the WSA have low favorability for metals, with low levels of confidence, while the remainder of the WSA, nearly two-thirds of it, has very low favorability for metals with low levels of confidence. Most of the WSA has moderate favorability for uranium, with a moderate level of confidence, but parts of the western edge have low favorability with low confidence. It has very low favorability for thorium, with low confidence. Two small areas have high to moderate favorability for beryl, with moderate confidence, and the southwestern edge has moderate favorability for lime or cement with moderate confidence. The remainder of the WSA has low favorability for nonmetallic minerals, with a low level of confidence. There is no known favorability for oil and gas, coal, oil shale, tar sands, or sodium and potassium. Parts of the western edge of the WSA have moderate favorability for geothermal resources with moderate confidence, while the remainder has low favorability with a low level of confidence. The principal recommendations for further work are that an effort should be made to acquire existing but unpublished geological mapping in the New York Butte quadrangle, and that the quadrangle be mapped to present-day U. S. Geological Survey standards, including alteration. I. INTRODUCTION The New York Butte G-E-M Resources Area (GRA No. CA-10) covers approximately 157,000 acres (637 sq km) and includes the following Wilderness Study Areas (WSAs): WSA Name WSA Number Cerro Gordo 010-055 Southern Inyo 010-056 The GRA is located in California in the Bureau of Land Management's (BLM) Bishop Resource Area, Bakersfield district. Figure 1 is an index map showing the location of the GRA. The area encompassed by the GRA is near 36°40' north latitude, 118 west longitude and includes the following townships: T 13 S, R 36,37 E T 15 S, R 36-38 E T 14 S, R 36,37 E T 16 S, R 37-39 E The areas of the WSAs are on the following U. S. Geological Survey topographic maps : 15-minute: Lone Pine New York Butte Independence The nearest town is Lone Pine which is located west of the GRA on U. S. Highway 395. Access to the area is via U. S. Highway 395 to the west and State Highways 190 and 136 to the southwest of the GRA. Access within the area is on Highway 190 adjacent to the Southern Pacific Railroad and Swansea Road and Cerro Gordo Road at the south end, both of which provide access to the southern part of the GRA. Most of the GRA is not accessible to vehicles. Figure 2 outlines the boundaries of the GRA and the WSAs on a topographic base at a scale of 1:250,000. Figure 3 is a geologic map of the GRA and vicinity, also at 1:250,000. At the end of the report, following the Land Classification Maps, is a geologic time scale showing the various geologic eras, periods and epochs by name as they are used in the text, with the corresponding age in years. This is so that the reader who is not familiar with geologic time subdivisions will have a comprehensive reference for the geochronology of events. This GRA Report is one of fifty-five reports on the Geology- A Emergy-Minerals potential of Wilderness Study Areas in the Basin and Range Province, prepared for the Bureau of Land Management by the Great Basin GEM Joint Venture. The principals of the Venture are Arthur Baker III, G. Martin Booth III, and Dennis P. Bryan. The study is principally a literature search supplemented by information provided by claim owners, other individuals with knowledge of some areas, and both specific and general experience of the authors. Brief field verification work was conducted on approximately 25 percent of the WSAs covered by the study. The WSAs in this GRA were field checked. One original copy of background data specifically applicable to this GEM Resource Area Report has been provided to the BLM as the GRA File. In the GRA File are items such as letters from or notes on telephone conversations with claim owners in the GRA or the WSA, plots of areas of Land Classification for Mineral Resources on maps at larger scale than those that accompany this report if such were made, original compilations of mining claim distribution, any copies of journal articles or other documents that were acquired during the research, and other notes as are deemed applicable by the authors. ^ As a part of the contract that resulted in this report, a background document was also written: Geological Environments of Energy and Mineral Resources. A copy of this document is included with the GRA File to this GRA report. There are some geological environments that are known to be favorable for certain kidns of mineral deposits, while other environments are known to be much less favorable. In many instances conclusions as to the favorability of areas for the accumulation of mineral resources, drawn in these GRA Reports, have been influenced by the geology of the areas, regardless of whether occurrences of valuable minerals are known to be present. This document is provided to give the reader some understanding of at least the most important aspects of goelogical environments that were in the minds of the authors when they wrote these reports. Figure 1. GRA Index Map of Region 3 1:3,168,000, Fresno and Death Valley Sheets New York Butte GRA CA-10 Figure 2 Fresno Sheet, Mathews and Burnett (1965); Death Valley Sheet, Streitz and Stinson (1974) New York Butte GRA CA-10 Figure 3 EXPLANATION SEDIMENTARY AND METASEDIMENTARY ROCKS I Qs Dune sand EH IGNEOUS AND META-IGNEOUS ROCKS Alluvium Stream channel deposits Fan deposits • Ow Recent volcanic: Orv' — rhyolite; Crv° — andesite; Grvb —basalt: Orv» —pyroclastic rocks Ot Basin deposits J Qsr Salt deposits Quaternary lake deposits Glacial deposits ED 1 Qm Quaternary nonmarine terrace deposits Pleistocene marine and marine terrace deposits I Oc Pleistocene nonmarine •Qov U k z HI U qp Plio-Pleistocene nonmarine Pleistocene volcanic: Opv —rhyolite: Qpv" -andesite; Cpv- —basalt; Opv" —pyroclastic rocks Quaternary and/or Pliocene cinder cones | Pc I Undivided PI locene nonmarine Puc Upper Pliocene nonmarine Pu Upper Pliocene marine Pliocene volcanic: pv' -rhyolite; Pv° — andesite; p D —basalt; Pvo —pyroclastic rocks Middle and/or lower Pliocene nonmarine Middle and/or lower Pliocene marine x < Mc Undivided Miocene nonmarine Muc I Upper Miocene nonmarine Mu Upper Miocene marine r "T-" — 1 Miocene volcanic: Mv' —rhyolite; Mv v. ° -andesite; Mv"— basalt; ' '■"• -j Mv" —pyroclastic rocks Mmc Middle Miocene nonmarine Mm Middle Miocene marine Lower Miocene marine Oligocene nonmarine Oligocene marine . . • • ; . ] Olit;ocene volcanic: 0v' — rhyolite; ■ Bv . 1 Ov" —andesite : OvB —basalt; — ' • * *l ©v0 — pyroclastic rocks Ec I Eocene nonmarine I I Eocene marine Eocene volcanic: Ev' —rhyolite; Ev° -andesite: Ev" -basalt; Ev°— pyroclastic rockf Epc Paleocene nonmarine r E>> Paleocene marine E? Paleocene marine Cenozoic nonmarme I Tc Tertiary nonmarme . Tertiary lake deposits Tm ; Tertiary marine EXPLANATION CONT. E Cenozoic volcanic: qt.' -rhyolite; QTv°— andesite: otv'' —basalt; 0TVD — pyroclastic rocks Tertiary cranitic- rocks Tertiary intrusive (hypabyssali rocks: Ti' -rhyolite; T.a -andesite; T.° -basalt Tertiary volcanic: TV —rhyolite; Tv° —andesite; Tv6 —basalt; Tv° —pyroclastic rocks oJ < [ Undivided Cretaceous marine Upper Cretaceous marine Lower Cretaceous marine Knoxville Formation Upper Jurassic marine Middle and/or Lower Jurassic marine Triassic marine Pre-Cretaceous metamorphic rocks (Is =• limestone or dolomite) Pre-Cretaceous metasedimentary rocks I Paleozoic marine ls I (Is = limestone or dolomite CP pSs Permian marine Undivided Carboniferous marine PS Pennsylvanian marine Mississippian marine Devonian marine Silurian marine Pre-Silurian meta- sedimentary rocks Ordovician marine Cambrian marine Cambrian - Precambrian marine Undivided Precambrian metamorphic rocks cCg = gneiss, oCs = schist Later Precambrian sedimentary and metamorphic rocks Earlier Precambrian metamorphic roci;s - Jfc*. Franciscan volcanic and metavolcamc rocks Mesozoic uranitic rocks: 9' -granite and adamellitt,:9,'-(£ranotlioritt'; v ' -tonalite and dioritc Mesozoic basic intrusive rocks Mesozoic ultrabasic intrusive rocks Jura-Trias metavolcanic rocks Pre-Cretaceous metavolcanic rocks qr-m I Pre-Cenozoic granitic and I metamorphic rocks Paleozoic metavolcanic rocks Permian metavolcanic rocks Carboniferous metavolcanic rocks Dv Devonian metavolcanic rocks Devonian and pre- Devonian? j metavolcanic rocks Pre-Silurian metamorphic rocks Pre-Silurian metavolcanic rocks EcC, I Precambrian igneous and I metamorphic rock complex If'Wsi -i Undivided &V--; >...,'■ I granitic Precambrian rocks pCjn Prccainhnaii anon hosiw ' II. GEOLOGY The New York Butte GRA encompasses the southern Inyo Mountains from Kearsage south to Keeler. The western escarpment of the Inyo Mountains forms the eastern boundary of the downdropped Owens Valley graben. The study area contains a transitional facies of thick sequences of Paleozoic sediments of the eastern carbonate assemblage and the western clastic assemblage, with Triassic marine sediments overlying them unconformably . These sediments have been folded and intruded by Cretaceous quartz monzonite stocks and plutons. Faults associated with the adjustment of the sediments to the intrusions have been noted. All known metalliferous ore deposits in the study area are genetically and spacially related to the Cretaceous intrusions. Basin and Range faulting during the Pliocene is responsible for the present topography. These normal faults trend predominantly to the northwest and parallel the Owens Valley "Earthquake" fault. 1. PHYSIOGRAPHY The New York Butte GRA encompasses the southern Inyo Mountains between the towns of Independence and Keeler, Inyo County, California. The Range trends northwest and lies between Owens Valley on the west and Saline Valley to the east. The northern portion of the study area is predominantly Jurassic-Cretaceous quartz monzonite of the Paiute Monument and the Pat Keyes intrusive bodies. A thin fringe of Paleozoic sediments is present along the range front in the north and comprise most of the total area in the southern portion of the GRA (Ross, 1967). Elevations along the crest of the range locally reach +11,000 feet and drainages predominantly run perpendicular to the northwest trend of the range. Faulting in the area generally parallels the northwest trend of the Basin and Range type escarpment along the range front. 2. ROCK UNITS The oldest rocks in the study area are Ordovician sediments of the Pogonip Group, overlain by Ordovician Eureka Quartzite. Above these are Silurian Devonian Hidden Valley and Ely Springs Dolomites, with Devonian Lost Burro Formation above them. 10 ^ The Mississippian Rest Spring shale (Ross, 1967), also called the Chainman shale in some publications (Merriam, 1963), was deposited conformably above the Lost Burro. Next were deposited limestones and shales of the Pennsylvanian Keeler Canyon Formation, overlain by shales and limestones of the Permian Owens Valley Formation which locally has a disconformity near the top. After a period of erosion that produced an unconformity, unnamed Triassic marine sediments, mostly limestone, were deposited upon the older sediments. An unnamed Triassic volcanic sequence was deposited above the sediments, its lower part sedimentary rocks of volcanic origin and its upper part similar material but with andesite flows and breccias. A very large pluton, known as the Hunter Mountain quartz monzonite in the northern part of the GRA, was intruded in Late Triassic-Jurassic. Smaller masses of granitic rocks were intruded in the central part of the GRA, probably during the Jurassic or Cretaceous. All of the known metallic mineralization in the GRA is apparently related to this epoch of intrusions. 3. STRUCTURAL GEOLOGY AND TECTONICS The oldest observable structures in the study area are broad folds formed by compressional forces during the Jurassic. These folds trend northwest and parallel the predominant fault trend. The predominant fold is a large syncline traceable from Waucoba Mountain to the southern end of the range. This syncline has been greatly faulted during two widely separated geologic periods, and disrupted by the intrusive bodies. Thrust faulting along the west front of the Inyos presumably was an effect of this folding. There are two major faults in the GRA, both trending northwest. One is near the west edge of the mountains, and for its entire 14-mile mapped length has dropped Permian Owens Valley Formation on the west side against Triassic volcanic rocks on the east side. The other is about five miles farther northeast, and in part offsets the Hunter Mountain pluton (Ross, 1967). Both of these faults, although roughly parallel to Basin and Range faulting, evidently had at least initial movement during or soon after the time of Cretaceous intrusions, since the western fault has been at least partly responsible for the localization of mineralization at a couple of places (field verification observation by A. Baker III). North and northeast-striking faults in the Cerro Gordo district in the south part of the GRA are thought to be of similar early origin (Merriam, 1963). Frontal faults of the Basin and Range type, none of which are shown on available maps and perhaps are not seen because of alluvial cover, undoubtedly outline the Inyo Mountains; most of the movement 11 r C on these presumably took place in the Pliocene and more recently. Close to the western edge of the New York Butte GRA is the "Earthquake" strike-slip fault in the middle of Owens valley which parallels the range front. Displacement on this fault caused the disastrous earthquake of 1867. 4 . PALEONTOLOGY Paleozoic marine sediments, in places abundantly fossiliferous occur within the New York Butte GRA. A general northeast strike is determined by regional synclinal structure, with Triassic and Jurassic rocks along the fold axis. Ordovician rocks equivalent to the Palmetto and Pogonip, in part, are exposed on the western margin of the GRA, but no fossil localities are known to be recorded from them. Elsewhere, however, these units are known to contain rich faunas of both the "shelly facies" (brachiopods, trilobites, corals) and graptolites, in the argillaceous shales. Devonian rocks, mostly carbonates and carbonaceous shales, contain abundant fossils near the top of the section, becoming rare in the more clastic underlying units. These units are exposed north of Cerro Gordo and at the eastern boundary of WSA CA-010-055 in Sections 1, 2, and 12, T 16 S, R 38 E, and parts of Sections 26, 27, 34, and 35, T 15 S, R 38 E. The Devonian fauna is characterized by brachiopods (dominated by Atrypa and Stropheodonta) , corals (Favosites), and occasional trilobites . Pennsylvanian (CP) and Permian (Pm) rocks, mostly carbonates, are widely distributed and commonly fossiliferous. Brachiopod and coral faunas from Mississippian carbonate units (CM) have been reported from T 16 S, R 38 E (University California Museum Paleontology) , but more precise locality data are not known. The Late Paleozoic Pennsylvanian and Permian faunas are dominated by fusulinids and brachiopods, usually exclusive of each other. Fusulinids, mostly Fusulina sp. (Pennsylvanian) occur in Section 2, T 17 S, R 38 E. Brachiopod index fossils are mostly Productids . Silurian carbonates, including massive dolomitic limestones, are sparsely fossiliferous. HISTORICAL GEOLOGY Precambrian and early Paleozoic sedimentation is not recorded in the GRA, although from regional mapping it must have taken place here. The oldest rocks exposed are Ordovician sediments, and sedimentation continued with one minor interruption through the Permian. Uplift caused an unconformity between the younger Paleozoic rocks and Triassic 12 r marine sediments deposited upon them. Triassic volcanic clastic sediments and flows were deposited conformably over the marine sediments. A period of compressive regional folding occurred during the late Jurassic and was followed by a period of intrusive activity related to the Sierra Nevada batholith during the Jurassic-Cretaceous. Faulting related to the displacement of the sediments by the intrusives occurred at this time, and mineralization in the areas is considered to be related to the intrusions . Basin and Range faulting during the Pliocene produced the present topography. 13 III. ENERGY AND MINERAL RESOURCES Note: Field verification in the New York Butte GRA was made on October 16-17, 1982 by Arthur Baker III, one of the authors of this report, and Richard W. Teixeira, Geology, Bishop Resources Area, BLM, by helicopter. The field verification work was entirely directed toward metallic mineral resources, and largely aimed toward confirming the existence and mineralization of known prospects and determining if there are prospects in the WSA that do not appear on maps . ( In general there are not prospects that do not appear on maps, except for several in Sec. 13, T 14 S, R 36 E projected, which had earlier been found by BLM personnel.) Twelve samples were collected and submitted to BLM for analysis. A list of the samples, with descriptive locations and descriptions of the material sampled, is in the GRA file, as are copies of the New York Butte and Lone Pine 15-minute topographic quadrangle maps on which are plotted the locations of the samples, and also a copy of the fire assay and spectrographic analysis reports by Metallurgical Laboratories, Inc. of San Francisco. Most of the area examined has not been surveyed for the land grid, so for locations townships, ranges and sections have been projected in from adjacent surveyed areas simply by extending the land grid lines shown on the topographic quadrangles. In general, the analyses confirmed the presence of low gold values, low to high silver values, low copper values, and low to high lead values in samples that by visual examination were expected to have at least some base metal values and probably silver values. The spectrographic analyses provide little information about the three altered zones sampled. A. METALLIC MINERAL RESOURCES 1. Known Mineral Deposits There is one major mining district in the GRA: the Cerro Gordo district, which is east of the south end of WSA CA 010-055, outside the WSA. This district, which operated in the late 1800s and again in the early 1900s is estimated to have produced $17 million (Goodwin, 1957) in silver, gold, lead and zinc from replacement orebodies in carbonate rocks (Merriam, 1963). The Burgess Mine, a gold producer (Norman and Stewart, 1951), is in WSA CA 010-056, near the middle of its east edge. It is at the contact of Triassic marine sediments with Triassic volcanic sediments in an area with numerous granitic, felsitic and andesitic dikes trending southeasterly from the southeast edge of the intrusive body that underlies New York Butte. The hornfelsed clastic sediments are, at least in part, heavily iron- 14 stained as though they were shattered and filmed with pyrite that is oxidized at the surface. Although the Burgess mine produced from a gold-bearing quartz vein, there are numerous places where the sediments have been replaced by pods of sulfides (mostly pyrite?) and a little magnetite. Old diggings and newer bulldozer cuts of unknown content and geology are scattered over an area of more than one square mile. The Burgess mine and its environs are essentially a small mining district of unknown production and, as far as published information is concerned, unknown geology or potential. Its isolation on top of the Inyo Range and being reachable only by two extremely rough roads, has no doubt impeded serious exploration of it. Two samples, #4 and #5, were taken here during field verification; sample descriptions are in the GRA file, with the descriptions of other samples taken that are mentioned below. Sample #4 was essentially barren. Sample #5, of quartz vein material with traces of copper stain, assigned 0.004 oz Au/ton, 9.87 oz Ag/ton and 4% Pb. Along the west front of the Inyos are numerous mines, outside the WSAs being considered here. Some of these are small replacement lead-silver deposits such as the Pennsylvania near Swansea (A. Baker III, personal communication) . Others are small silver-lead veins with quartz. There seem to be few, if any, gold mines or prospects here (Goodwin, 1957, Plate 1). There are also several limestone and dolomite quarries, none of which are known to be active at present. Within the WSAs there are more than a dozen old mines and prospects, excluding those in the Burgess "district". Most of these were examined (by landing from helicopter) in the field verification made on October 16 and 17, 1982. They are as follows (both mines — that clearly had production — and prospects will be described here, for simplicity) . WSA CA 010-055 Unnamed prospect in Sec. 17, T 16 S, R 38 E projected, shown as prospect symbol on New York Butte topographic quad. (Lost Frenchman? MILS location in Sec. 16, lead- silver-copper). It was not found despite intensive helicopter search in the immediate area. Flagstaff Mine, in Sec. 7, T 16 S, R 38 E projected, (Merriam, 1963, Plate 2), is not shown on the New York Butte topographic quadrangle. The workings are adjacent to the Swansea road. Several adits on the north and south sides of a draw are on a vein striking due north to north 60 west, nearly vertical and about parallel to schistosity of the Owens Valley formation which here is phyllite with 15 thin limestones. Sample #2 is of a six inch quartz vein in the north adit portal (see GRA file). It assayed 0.025 oz Au/ton, 1.24 oz Ag/ton, 0.6% Pb. One hundred feet or less east of the vein is the major northwest fault. East of this for a 150-foot width the Triassic volcanic sediments are intensely sheared and iron-stained, with a few stringers up to 2 inches wide of copper oxides mostly crosswise to the shearing. The length of this zone is at least 500 feet. Sample #3 is a chip sample across this zone in the draw bottom, avoiding visible copper. The spectrographic analysis of the sample provides no useful information. From the helicopter several adits were visible in a draw about one-quarter mile north, also very close to Swansea road, which were not examined. WSA CA 010-056 Unnamed prospect in Sec. 28, T 15 S, R 37 E projected, a pair of adit symbols on the New York Butte topographic quadrangle map. These were not examined on the ground because it was too long a walk for the time available from the nearest helicopter landing site. From the air, the adit dumps are small and white. This may be the Big Horn uranium prospect listed as in Sec. 29 in MILS. Unnamed prospect symbol, Sees. 22, 23, T 15 S, R 37 E projected, New York Butte quad, essentially at the west edge of the Burgess district. A 50 foot inclined shaft is on two intersecting quartz veins six inches wide, apparently not more than 20 feet long with attitude about N 70 W, 60 N. Sample #12 is a grab of dump high-grade: sugary quartz with some vugs, rare pyrite cubes, and nothing else visible. It assayed 0.06 oz/ton Au, 0.02 oz/ton Ag, 0.015 % Pb. This may be the Nellie H gold- copper prospect listed in MILS as in Sec. 15, or the franklin D. Roosevelt lead prospect in Sec. 15. Unnamed prospect, Sec. 21, T 15 S, R 37 E, projected, adit symbol labelled "tunnel" on New York Butte quad. The country rock is phyllite with limestone beds, sheeted about N 60 W, 80° NE. Pockety quartz veins up to three feet wide strike N 20-40° W, and are about vertical, with pockets of limonite also about vertical and not more than 10 feet long. Near this point are a couple of shafts less than 100 feet deep and a 100-foot adit around the ridge to the east. Sample #1 is of high-grade on the dump of the ridge-top shaft: quartz with a little galena and traces of copper stain. It assayed 0.004 oz/ton Au, 2.54 oz/ton Ag, 0.04% Cu, and 0.60% Pb. Unnamed prospect in Sec. 7, T 15 S, R 37 E projected, adit symbols labelled "tunnels" on New York Butte quadrangle. There is a 10-foot to 50-foot wide zone of intensely sheared rock, partly conglomerate, a quarter of a mile 16 long striking N 80 W, with some iron staining. In the zone are occasional irregular quartz veins up to one foot wide, apparently not more than 25 feet long, mostly cross- wise to shearing of the zone. The quartz has small spots and clots of limonite that appears to be derived from siderite, with no visible copper or lead. Sample #11 is chips from a pile of quartz on the dump of the upper, 10- foot adit. It assayed 0.008 oz/ton Au, 0.28 oz/ton Ag, 0.06% Cu, 0.40% Pb, 0.35% Zn. Duarte mine, Sec. 1, T 15 S, R 37 E projected, New York Butte quadrangle. The adit shown on the quadrangle was not accessible in the time available, so a 15-foot adit about 300 yards east of Duarte in same zone N 70° W, 35- 45 ° NE was examined. The zone is 20 to 50 feet wide, intensely sheared, of lightly iron stained hornfels and perhaps partly rhyolitic dike with rare spots of copper stain. There are occasional lenses of vuggy quartz up to one inch wide and about one foot long. The hornfels in this area has somewhat more visible epidote than elsewhere, and some float fragments have knots of garnetite an inch or two in diameter, not seen elsewhere. A few float fragments of magnetite, up to fist-size, were also seen. Sample #10 is a 10-foot chip through part of the shear zone in the west wall of the adit. The spectrographic analysis of the sample shows relatively higher values in base and precious metals than do the analyses of other altered material (Samples Nos. 3 and 9). Unnamed prospect in Sec. 31, T 15 S, R 38 E projected, one mile east of the Duarte mine, could not be found with intensive air and ground search. Monte Carlo mine (Goodwin, 1957), Sec. 14 T 14 S, R 36 E projected, shown as a line of adit and prospect symbols half a mile long on the Lone Pine quadrangle. Goodwin credits the mine with over 100,000 ounces of recorded silver production before 1902, as well as later unspecified production. The vein strikes N 80 W and dips steeply north. It was examined at a couple of prominent pits and/or glory noles near its east end. The vein here is locally as much as 12 feet wide, mostly sugary quartz with irregular areas up to a couple of feet wide containing numerous irregular narrow galena veinlets. The north side of the vein has been stoped to surface for a width of three feet and a length of at least 25 feet. Sample #6 is of high-grade piled on the dump, quartz with galena. It assayed 0.055 oz/ton Au, 11.40 oz/ton Ag, and "major" Pb. The lowest, westernmost adit of the Monte Carlo apparently is outside the WSA as drawn, but the other workings are within the WSA. Unnamed prospects in Sec. 13, T 14 S, R 36 E projected, about a mile northeast of Monte Carlo, not on Lone Pine quadrangle but found earlier by BLM reconnaissance. 17 Quartz veins are in hornfels, with maximum width of 2 feet and N 20-40 E strike with steep easterly dips. Sample #7 is of sugary quartz with light copper stain and rare spots of galena up to one-half inch diameter, from the dump of an adit northeast of the saddle above the "7200" contour designation. It assayed 0.002 oz/ton Au, 0.15 oz/ton Ag, 0.6% Pb and 0.4% Zn. Sample #8 is of quartz with abundant galena and fairly abundant copper staining, from the dump of an adit south of the saddle. Most of the vein in place appears barren, but in a partly-caved glory hole there is similar material in place, one foot wide. A third adit, on the north side of the saddle and 25 feet below it, has a similar barren vein exposed and material on the dump much like that of the Monte Carlo. Unnamed prospect in Sec. 10, T 14 S, R 36 E, about 1 mile south of Reward on Lone Pine quadrangle but not shown on the quadrangle map; the adit was seen from the air but not examined on the ground. It apparently is within WSA 010- 056. This may be the Hirsh gold-lead-silver-copper mine of MILS, listed as in Sec. 3. 2. Known Prospects, Mineral Occurrences and Mineralized Areas Prospects and mineral occurrences examined during field verification have been described above. The altered zone in Triassic volcanics adjacent to the Flagstaff mine has been described above. Ground color variations seen from the helicopter northwest of the Flagstaff may be a continuation of this zone, mostly covered by colluvium; if so, the zone may be half a mile long, or more. From the site of the not-found adit a mile east of the Duarte mine (Sec. 31, T 15 S, R 38 E projected) a zone of dark red alteration locally several hundred feet wide could be seen half a mile north. The zone, roughly plotted on the field copy of the New York Butte quadrangle that is in the GRA file, trends about N 40 W and is at least half a mile long. In Sec. 13, T 14 S, R 36 E, just north of the adits of samples #7 and #8, is a similar northwest-trending zone of dark red alteration. This is at least several hundred feet long with very erratic width of from 10 feet to 50 feet. It is a dense, dark gray felsite with very abundant fine-grained pyrite preserved in the interior of pieces even at the surface. Sample #9 is of this material. The spectrographic analyses of this sample provides no useful information. 18 * MILS data lists about a dozen prospects in Sees. 15 and 16, T 16 S, R 38 E, in the south end of WSA CA 010-055. The New York Butte quadrangle does not show any prospects in these sections, and none were seen in field verification helicopter reconnaissance. 3. Mining Claims Plotting of patented claims shows three sections with claims that might be within WSA CA 010-05 5. Two of these are in the southeast corner of the WSA, near Cerro Gordo, and may well be outside the WSA boundary. The third is east of Swansea and also may be outside the boundary. Two patented sections with claims plot in WSA CA 010-056, both in the vicinity of Long John Canyon. One of these probably is on one of the mines in the Canyon and outside the WSA. The other appears to be well within the WSA and may cover the property in Sec. 21, T 15 S, R 37 E described above. The southern part of WSA CA 010-055 is essentially solidly covered with unpatented claims in a band extending westward from Cerro Gordo; this is the same area as the prospect locations cited in MILS, mentioned above, in which helicopter reconnaissance showed no old diggings. Near the middle of the northeast border, south of the old tramline, claims are plotted that may be within the WSA, close to the Cerro Gordo-Burgess road. There are a great many unpatented claims in WSA CA 010- 056. A few of them are in the vicinity of the Burgess Mine, but most are along the west side of the WSA in country that is relatively accessible but nonetheless extremely rugged. Some of them undoubtedly cover some or all of the old mines and prospects described above. 4. Mineral Deposit Types All of the metallic mineral deposits known in the WSAs fall into one or the other of two categories: quartz veins with primarily gold values, and quartz veins with primarily silver-lead values. The Burgess vein and probably the Flagstaff vein fall into the first category. These are mesothermal veins related to the granitic intrusions. The Burgess vein was not seen at any point, so its size is unknown. The Flagstaff vein is visible in several of the adits driven on it; at the portals it is nowhere more than a few inches wide, and at some places there seems to be no vein at all, only a shear zone a few inches wide which may carry gold values. 19 All the other mines and prospects examined belong to the second category, quartz veins with silver-lead values — as indicated by the presence of galena in them. They may also have substantial gold values, since most descriptions of mines in this region mention gold production. These, too, are mesothermal veins related to the granitic intrusions . The large lead-silver orebodies of the Cerro Gordo district were almost all replacement bodies — not veins - - in the Devonian Lost Burro Formation (Merriam, 1963), as were at least those of the Pennsylvania mine in the Swansea district (A. Baker III, personal communication). The only place where the Lost Burro Formation is exposed within the WSAs is a small strip in the vicinity of Sec. 28, T 15 S, R 37 E as nearly as Ross' (1967) generalized geology can be plotted; the two adits in this section that were not examined during the field verification may be in the Lost Burro Formation. The Formation should be present at considerable depth under the WSAs. Small bodies of iron oxides found at some localities during the field verification — notably south of Long John Canyon and near the Burgess mine, as described above — are the oxidized remains of replacement sulfide bodies in limestone. Judging by the nature of the iron oxides, and also the fact that none of the bodies appear to have been extensively mined or prospected, these replacement bodies probably originally consisted almost entirely of pyrite, rather than lead and zinc sulfides. Their existence suggests that it is possible there are lead- zinc-silver replacement deposits somewhere in the limestones and dolomites inside the WSAs, although none have been found and the highly favorable Lost Burro limestones are not present near the surface. The significance of the altered zones seen in the field verification is unknown. The two in WSA CA 010-056 are not related to any known mineralization other than the abundant pyrite seen disseminated in the one zone and inferred to be in the other zone. The altered zone in WSA CA 010-055 lies along a major fault, contains visible copper mineralization, and is immediately adjacent to the gold(?) vein of the Flagstaff mine, all of which suggest that it may have significance that could lead to mineral resources . Mineral Economics Most of the veins in the WSAs are narrow and probably irregular. They are not likely to be of interest to major mining companies because their size precludes any expectation of substantial tonnages of ore. However, depending on metal values and metal prices, it is possible 20 that some of them could be mined by small organizations. Most of them have formidable problems of access : in the early days everything that went into them or came out of them was carried on the backs of men, burros or mules. Road building to them would be extremely expensive. The Monte Carlo lead-silver mine in WSA CA 010-056 may be an exception to these generalizations: the vein is large although the size of ore shoots in it is unknown, and at least the lowest part is readily accessible. The Flagstaff mine and the Burgess district are exceptions to the access generalization since they lie on the Swansea road, though it is described as a very poor road suitable only for four-wheel drive vehicles. The major uses of silver are in photographic film, sterlingware, and increasingly in electrical contacts and conductors. It is also widely used for storage of wealth in the form of jewelry, "coins" or bullion. Like gold it is commonly measured in troy ounces, which weigh 31.1 grand grams, twelve of which make one troy pound. World production is about 350 million ounces per year, of which the United States produces about one-tenth, while it uses more than one-third of world production. About two- thirds of all silver is produced as a byproduct in the mining of other metals, so the supply cannot readily adjust to demand. It is a strategic metal. Demand is expected to increase in the next decades because of growing industrial use. At the end of 1982 the price of silver was $11.70 per ounce. The major use of gold is for storing wealth. It is no longer used for coinage because of monetary problems, but many gold "coins" are struck each year for sale simply as known quantities of gold that the buyer can keep or dispose of relatively easily. The greatest other use of gold is in jewelry, another form of stored wealth. In recent years industrial applications have become increasingly important, especially as a conductor in electronic instrumentation. In the United States and some other countries gold is measured in troy ounces that weigh 31.1 grams — twelve of which make one troy pound. Annual world production is about 40 million ounces per year, of which the United States produces somewhat more than one million ounces, less than one-fourth of its consumption, while the Republic of South Africa is by far the largest producer at more than 20 million ounces per year. World production is expected to increase through the 1980s. For many years the price was fixed by the United States at $35 per ounce, but after deregulation the price rose to a high of more than $800 per ounce and then dropped to the neighborhood of $400 per ounce. At the end of 1982 the price was $460.50 per ounce. 21 The largest use for lead is in electrical storage batteries, the second being a gasoline antiknock additive. It has many other uses, however, including radiation shielding, solders, numerous chemical applications and in construction. About four million metric tons of lead are produced in the world annually. The United States produces about half a million tons per year, and recovers about the same amount from scrap — much of it through the recycling of old batteries. It imports about one-quarter of a million tons. Lead is classified as a strategic mineral. Demand is projected to increase somewhat in the next couple of decades, but environmental concerns will limit the increase. The United States has large ore reserves that are expected to last well beyond the end of this century at current production rates even without major new discoveries. At the end of 1982 the price was about 22 cents per pound. The largest use for copper is in electrical equipment and supplies and in smaller-guage wire where its electrical conductivity is essential. It is also used in large quantities in applications where its corrosion resistance is important — in housing, brass and bronze, sea-water corrosion resistant alloys and others. It is used also in ammunition, many chemicals, and in applications where its conductivity of heat is important. World production is about 7.5 million metric tons annually, of which the United States produces about 1.5 million tons, nearly sufficient to satisfy domestic demand. Copper is a strategic metal. There are large reserves of coppper ore in the world, and the United States has greater reserves and greater resources than any other country. United States demand is expected to nearly double by the year 2000, but reserves are thought to be sufficient to meet the demand. However, environmental problems of smelting copper may hinder production, and in times of low prices foreign producers tend to maintain full production for political reasons, while domestic producers tend to restrict production for economic reasons. These pressures on the domestic copper industry weaken its competitive capability on the world market. At the end of 1982 the price of copper was 73 cents per pound. B. NONMETALLIC MINERAL RESOURCES 1. Known Mineral Deposits Two tons of hand-cobbed beryl ore are reported produced from a deposit in Sec. 8, T 15 S, R 37 E (Benson, 1962) or Sec. 29, T 15 S, R 37 E in WSA CA 010-056 (Davis, 1983). Relatively large quantities of limestone and dolomite have been mined along the western front of the Inyo Range immediately west of the western boundary of WSAs CA 010- 22 055 (Logan, 1947). There are no known quarries within the WSAs and no evidence that any serious attention has been given to limestone and dolomite prospecting — there is plenty of material easily available along the mountain edge, which offers little incentive to prospect for such low-priced commodities in the rugged higher mountains. Talc and quartzite have been mined just west of the western boundaries of both WSAs according to Davis (1983), who quotes Ver Planck (1966) to the effect that the Eureka quartzite here is one of the very few sources of high- purity quartzite in California. Large quantities of talc have been produced from the Bohnam talc deposits east of WSA CA 010-055. Some of these deposits have been mined within half a mile of the WSA boundary, but there is nothing to indicate that the talc extends within the WSA. 2. Known Prospects, Mineral Occurrences and Mineralized Areas There are numerous prospects on limestone, dolomite and talc in the GRA, but none are known within either of the WSAs. A beryl occurrence is reported in Sec. 19, T 15 S, R 37 E in WSA CA 010-056 (Benson, 1962 and Davis, 1983). Mining Claims, Leases and Material Sites It is not known whether any of the mining claims within the WSAs are on nonmetallic mineral occurrences. No nonmetallic mineral occurrences are known within the WSAs. No material sites are known within the WSAs. 4. Mineral Deposit Types At the mine that produced two tons of beryl ore, the beryl occurs in granitic rocks near the contact with limestone, while at the other prospect it occurs as crystals in granitic rocks (Davis, 1983). It is worth noting that almost any rock can be developed into a saleable nonmetallic commodity, especially if it has some unusual characteristic which may be as simple as a particular color or a special mineral makeup. Thus, the WSAs have potential for nonmetallic deposits even though none other than the beryl occurrences are known to exist there. 23 5. Mineral Economics Nonmetallic mineral deposits that might be developed in the New York Butte GRA share a problem common to all nonmetallics in the Owens Valley area — their considerable distance from the major marketing area of Los Angeles. To be economically exploitable, they must be unusual enough that similar deposits cannot be found closer to Los Angeles that would have the advantage of a shorter haul. Pure limestone and dolomite are used principally to produce lime, but some is used as rock for building stone, crushed rock, and similar applications. The principal uses of lime are in steel smelting, water purification, as an alkali, in paper and pulp manufacture, and sewage treatment. Other uses for lime are in sugar purification, mortar, and as an agricultural soil conditioner. Limestone with certain clay impurities (called cement rock), or purer limestone with clay added, is used to make cement that is mostly consumed in construction. The United States uses about 20 million tons of lime and 85 million tons of cement annually. For both lime and cement the raw material must be mined within a very few miles of the processing plant, because it has a very low value in the form of run-of-mine rock — two or three dollars per ton. There are numerous lime and cement plants in the United States, and most of them sell most of their product within a 200 mile radius of the plant. Some cement is imported in the form of clinker, which is the kiln-fired rock that is then ground in the United States. In the early 1980s the price F.O.B. plant of both lime and cement is about $40 per ton. Talc and pyrophyllite are two different minerals but have somewhat similar chemical compositions and physical characteristics, so they can be used interchangeably in some applications but also each of them has applications in which it is more suitable than the other. Most available economic data treat the two minerals (and small amounts of others) together, so they are treated this way here and the term talc is used to include all the talc- like minerals. About one-fourth of all talc is used in ceramics, with a somewhat smaller portion used in paint and a still smaller portion in plastics as a filler; these three uses account for about two-thirds of talc consumption. The most well-known use, in talcum powder and other cosmetics, uses only about 7 percent of total comsumption. Pyrophyllite as such is particularly heavily used in insecticides and refractories. United States consumption of talc is about one million short tons per year and production is about 1.3 million tons per year with the average being exported. Talc consumption is forecast to about double by the year 2000, with domestic production increasing enough to keep up with demand but 24 * exports probably ceasing. The price of crude talc as mined is about $15 per ton, while processed talc sold by producers (principally ground), is about $65 per ton. About 80 percent of beryllium is used in alloys, mostly with copper, and most of the alloys are used in electrical applications such as springs, contacts, relays and other equipment. Some is used in aerospace applications, either in alloys or as beryllium metal which has high strength, light weight and excellent anticorrosion characteristics. The United States consumes about 300 tons of beryllium annually, probably more than half of which is produced domestically. Beryllium consumption is not expected to change greatly by the year 2000, partly because it can be highly toxic especially while being processed, so other materials are used in its stead wherever possible. The mineral beryl, which contains about 11 percent beryllium oxide and is one of the major ores of beryllium, is priced at about $475 per ton, though all sales are negotiated. Some beryl is used as a semi-precious gemstone, and one variety, the emerald, is highly prized. C. ENERGY RESOURCES Uranium and Thorium Resources 1. Known Mineral Deposits There are no known uranium or thorium deposits within or near the WSAs or the GRA. 2. Known Prospects, Mineral Occurrences and Mineralized Areas There are no known thorium occurrences within the WSAs or the GRA. Radioactive occurrences are indicated on the Land Classification and Mineral Occurrences Map included at the back of the report. The Big Horn or Lucky Strike uranium prospect is in Sec . 29 (projected), T 15 S, R 37 E (Minobras, 1978) within WSA CA 010-056. The mineralization occurs in granite. No further information as to the size or type of deposit is available . 3. Mining Claims The Big Horn Prospect is the only known uranium claim within the GRA, and it has probably lapsed. There are apparently no thorium claims within or near the GRA. 25 4. Mineral Deposit Types Lack of known mineral occurrences prevents a description of deposit types for the GRA. 5. Mineral Economics Lack of known mineral occurrences prevents an economic determination though both uranium and thorium appear to be of no economic importance for the area. Uranium in its enriched form is used primarily as fuel for nuclear reactors, with lesser amounts being used in the manufacture of atomic weapons and materials which are used for medical radiation treatments. Annual western world production of uranium concentrates totaled approximately 57,000 tons in 1981, and the United States was responsible for about 30 percent of this total, making the United States the largest single producer of uranium (American Bureau of Metal Statistics, 1982). The United States ranks second behind Australia in uranium resources based on a production cost of $25/pound or less. United States uranium demand is growing at a much slower rate than was forecast in the late 1980s, because the number of new reactors scheduled for construction has declined sharply since the accident at the Three Mile Island Nuclear Plant in March, 1979. Current and future supplies were seen to exceed future demand by a significant margin and spot prices of uranium fell from $40/pound to $25/pound from January, 1980 to January, 1981 (Mining Journal, July 24, 1981). At present the outlook for the United States uranium industry is bleak. Low prices and overproduction in the industry have resulted in the closures of numerous uranium mines and mills and reduced production at properties which have remained in operation. The price of uranium at the end of 1982 was $19.75/pound of concentrate. Thorium is used in the manufacture of incandescent gas mantles, welding rods, refractories, as fuel for nuclear power reactors and as an alloying agent. The principal source of thorium is monazite which is recovered as a byproduct of titanium, zirconium and rare earth recovery from beach sands. Although monazite is produced from Florida beach sands, thorium products are not produced from monazite in the United States. Consequently, thorium products used in the United States come from imports, primarily from France and Canada, and industry and government sotcks . Estimated United States consumption of thorium in 1980 was 3 3 tons, most of which was used in incandescent lamp mantles and refractories (Kirk, 1980b) . Use of thorium as nuclear fuel is relatively small at present, because only two commercial thorium- fueled reactors are in operation. Annual United States demand 26 for thorium is projected at 155 tons by 2000 (Kirk, 1980a). Most of this growth is forecast to occur in nuclear power reactor usage, assuming that six to ten thorium- fueled reactors are on line by that time. The United States and the rest of the world are in a favorable position with regard to adequacy of thorium reserves. The United States has reserves estimated at 218,000 tons of ThO? in stream and beach placers, veins and carbonatite deposits (Kirk, 1982); and probable cumulative demand in the United States as of 2000 is estimated at only 1,800 tons (Kirk, 1980b) . The price of thorium oxide at the end of 1981 was $16.45 per pound. Oil & Gas Resources There are no oil and gas fields, hydrocarbon shows in wells, or surface seeps in the region; nor are there any Federal oil and gas leases in the immediate region. The stratigraphy within the GRA is not conducive to the generation of petroleum hydrocarbons. There is no oil and gas lease map, no oil and gas occurrence and land classification map in this report. Geothermal Resources 1. Known Geothermal Deposits There are no geothermal deposits within the New York Butte GRA, nor adjacent to it on the western flank of the southern Inyo Mountains. 2. Known Prospects, Geothermal Occurrences, and Geothermal Areas On the southern boundary of the GRA or just to the south there are unnamed springs which have a temperature of 30 °C (Geothermal Occurrence and Land Classification Map) . The computed estimate of the total dissolved solids is 2,150 mg/1, and the flow is 57 l/min at the edge of Owens Lake. Eleven miles to the south, also at the edge of Owens Lake, the 183-meter Dirty Socks Hot Springs well has a temperature of 34°C, a flow of 380 l/min, and a salinity of 5,530 mg/1 (NOAA, 1982). In Saline Valley, on the opposite flank of the Inyo Mountains, there are four thermal occurrences: 27 Flow TDS Spring Temp. (l/min) (mg/1) Upper Warm Spring Warm Palm Spring 49 °C 1000 Lower Warm Springs 43 °C 1050 ♦ Little Hunter Canyon Springs 27 °C 568 540 3. Geothermal Leases Within the Owens Lake valley on the east side where Kerr- McGee Corporation operates a salt-winning operation from brines, there are at least 13 Federally-administered geothermal leases in a contiguous block (Geothermal Lease Map) . Five of these are within the GRA between the lake and the Inyo Mountains . Six miles east of the northeastern corner of the GRA in Saline Valley, the U.S. Geological Survey has designated five sections as Saline Valley KGRA for leasing purposes. There are no leases in this prospect area. 4. Geothermal Deposit Types Data is not available from which to determine the type of prospect at the Salt Works, but it is expected that the thermal waters are part of a deep hot water system circulating upwards along Basin and Range faults. 5. Geothermal Economics There is no data upon which to base the economics of a geothermal system. It is likely that the lessee may plan to develop the resource for direct use, and if temperatures permit, for electrical power as well. Geothermal resources are utilized in the form of hot water or steam normally captured by means of drilling wells to a depth of a few feet to over 10,000 feet in depth. The fluid temperature, sustained flow rate and water chemistry characteristics of a geothermal reservoir determine the depth to which it will be economically feasible to drill and develop each site. Higher temperature resources (above 350 °F) are currently being used to generate electrical power in Utah and California, and in a number of foreign countries. As fuel costs rise and technology improves, the lower temperature 28 limit for power will decrease appreciably — especially . IV6S. Aite of mann« Pleistocene of California: Am. A-N«e. IVtruleum liruliUKti. v. t'J. no. 7. p l'">7 f..r the PI, iiUwrnr of mouthem California. - Geological Society of Uindon. li»>4. The Phanmnoic nm.-.cale. a ijrupunum: Cevl. Sue. London. Quart. Jour., v. 120, nvjpp . p. 21*0-2*2. for Lhe Mi.wene thr. mh Ihe Cambrian. 'Stern. T W.. written eommun.. 1'Jbtt. for the Pircambrian 4 Include* provincial »eri<-s accepted for u»e in U S. Geological Survey report*. Term-- designating time are in parentheses Informal time term* early, middle, and l»Le may be used for the eras, and for periods where there it no formal subdivision into Early. Middle, and Late, and for epochs. Informal nvk urmi lower, middle, and upper may be u«cd where there u no formal subdivision of a system or of a Hcriea. GF.OI.OCIC NAMES COMMITTEE. 1970 1 r