s; 7
I4,.y4 . /<JyuJ?t (f^ /J^H^^yi^^LuZfj'
OFFICE OF INDIAN AFFAIRS
FARM AND HOME MECHANICS
SOME THINGS THAT EVERY BOY SHOULD KNOW HOW TO DO
AND HENCE SHOULD LEARN TO DO IN SCHOOL
WASHINGTON
GOVERNMENT PRINTING OFFICE
1911
OFFICE OF INDIAN AFFAIRS
FARM AND HOME MECHANICS
SOME THINGS THAT EVERY BOY SHOULD KNOW HOW TO DO
AND HENCE SHOULD LEARN TO DO IN SCHOOL
^
^^/Ty^3
WASHINGTON
GOVERNMENT PRINTING OFFICE
1911
a. Liiftt ^^
v.^ i.
V-U
'^\\
This publication is distributed free only to the officers of
the United States Indian Service. Persons desiring copies
for their personal use may obtain them from the Superin-
tendent of Documents, Government Printing Office, Wash-
ington, D. C, for 15 cents.
2
CONTENTS.
Page.
Preface 5
Introduction 7
Lists of tools 9
Cost of equipment for wood-working classes 10
Split-log drag 11
How to use a drag 11
Setting posts 12
Building fence 12
Planting trees 12
Oiling and mending harness 13
Caring for farm and other tools 13
Pruning 13
Protecting trees 14
Putting handles in tools 14
Nailing on horseshoes 14
Sharpening plows 15
Mixing mortar _ 15
Laying cement walks 15
Laying stone wall 17
Hanging doors 17
Setting locks 18
Painting and glazing 18
Building roads 19
Glueing 20
Soldering 20
Harnessing, hitching, and unhitching horses 21
ILLUSTRATIONS.
Page.
Plate I. Cheap workbench 48
II. Manual training workbench 48
III. Details of manual training workbench 48
IV. Domestic science cook table 48
V. Ironing board to be used with domestic science cook table 48
Fig. 1. Breadboard 22
2. Stall, feed box, and manger 23
3. Hen's nest 24
4. Henroost .• 25
5. Gate 26
6. Chicken coop 27
7. Milk stool 28
3
4 ILLUSTRATIONS.
Page.
Fig. 8. Evener 28
9. Feed trough 29
10. Water trough 30
11. Wall shelf 31
12. Hangingshelf 32
13. Footstool , 33
14. Flour box 34
15. Bench 35
16. Knife box 36
17. Table 37
18. Cupboard 38
19. Towel roller 39
20. Bedstead 40
21. Window screen 41
22. Door screen 42
23. Bookcase 43
24. Tool chest 44
25. Clothes box 45
26. Split-log drag 46
27. Hayrack .._ 47
28. Details of a cheap workbench 48
PREFACE.
This publication has been compiled from the results of practical
experience in the work of instruction in the Indian schools. It is
believed that it is a comprehensive and practical manual that will
be of material assistance to the teacher, but every teacher is urged
to forward suggestions in order that the manual may be improved
when a second edition is issued.
One word of caution is urged a^ to the use of this publication. The
teachers should look at it in the light of suggestions rather than as
dogma from which they should never deviate, and I should not want
any teachers to feel that they could not take up any phases of the
subject or any methods of instruction which are not contained in
this publication. Conditions vary greatly in different localities and
in the same locality at different times, and the teacher must ever
be alert to meet these changes. Perhaps this word of caution is
unnecessary, but the experience of many school systems goes to
show that it can not be too strongly emphasized.
R. G. Valentine, Commissioner.
THINGS THAT EVERY BOY SHOULD KNOW HOW TO DO.
INTRODUCTION.
Nearly every Indian boy when at home Hves in the country rather
than in town, and therefore is more or less closely in touch with farm
life. The majority of these boys have their own land, and this
majority should ultimately make their living from this land. To do
that requires that they live the lives of farmers. There are many
simple processes which the white boy who is brought up on a farm
learns incidentally at home that the Indian boy has no opportunity
to learn there, but wliich he must know how to do if he is to make a
real success of his farming.
The boy who devotes himself entirely to a trade may become pro-
ficient in that trade, and yet may lack in the general knowledge of
doing these common things that are so necessary to the farm and
home.
A suggestive list is given containing a number of common articles
that have to be made for every home and on every farm, together
with a number of processes with which every boy should be famihar.
There are localities to which not all of these suggestions may apply,
and it will be desirable to add to tliis list some things that are appli-
cable only to certain local requirements. It is not the purpose of the
bulletin to furnish any complete list or complete course, but merely
to give suggestions as to what may be done, with the expectation
that the live instructor will add to the lists as his experience may show
him is advisable.
The cuts contained in the bulletin will show how the more difficult
articles are made and the description of the processes will be sufficient
to give any instructor a good idea of what is to be done if he is not
already informed on the -subject.
The records should be kept on cards, as shown on the sample, and
due credit should be given for everything that is done when the pupil
has acquired the ability to do the thing independently. These
records should show exactly what the pupil has done, not only in the
way of completing the work as outhned but also in connection with
his work in a regular trade, if he is taking such a course. The card
should be filed in the pupil's individual folder with all other perma-
nent records.
The earnest cooperation of all employees is I'&quested in carrying
out and adding to the plan as outlined.
FARM AND HOME MECHANICS.
Name
Date of entry.
Sample record card {face.)
Age
Term
Tribe
School grade .
Article.
Date.
Process.
Date.
Remarks.
1907.
1907.
1
Sept. 25
1
Oct. 6
7
Oct. 3
2
Nov. 13
10
Oct. 15
9
Nov. 17
2
Nov. 20
4
Dec. 15
11
Nov. 20
5
Dec. 15
12
Nov. 20
e
Dec. 15
3
Dec. 10
1908.
1908.
3
Apr. 17
23
Jan. 5
17
June 12
13
Feb. 2
11
Oct. 2
4
Mar. 30
10
Dec. 15
18
June 15
17
Sept. 30
1909.
27
Oct. 23
21
Feb. 20
31
Nov. 5
12
May 13
14
Nov. 30
16
June 11
20
Dec. 20
23
13
June 15
Oct. 18
1909.
19
Nov. 3
5
Jan. 30
20
Nov. 3
6
Feb. 25
24
Mar. 29
1910.
9
Apr. 19
18
Jan. 7
8
May 27
8
Mar. 5
15
Oct. 3
14
May 13
26
Nov. 20
15
22
May 31
June 5
1910.
7
June 15
19
Jan. 5
22
Mar. 2
33
Apr. 17
34
June 15
Sample record card (reverse.)
This card is to be used in recording the work done by each boy during his attend-
ance in school. All of the articles mentioned may not be applicable to each individ-
ual and it may be desirable to teach other processes and the making of other articles
in different localities, but whenever anything is made that is not in the list, or when
anything practicable is taught that is not found there, these should be inserted with
appropriate number and the proper credit given.
ARTICLES TO BE MADE.
1. Bread board.
16.
Knife box.
2. Stall, feed box and manger.
17.
Table.
3. Hen's nest.
18.
Cupboard.
4. Hen roost.
19.
Towel roller.
5. Gate.
20.
Bedstead.
6. Chicken coop.
21.
Window screen.
7. Milk stool.
22.
Door screen.
8. Evener.
23.
Bookcase.
9. Trough, feed.
24.
Chest.
10. Trough, water.
25.
Clothes box.
11. Shelf, wall.
26.
Split-log drag.
12. Shelf, hanging.
27.
Hay rack.
13. Footstool.
28.
Cheap workbench.
14. Flour box.
29.
Manual training workbench
15. Bench.
FAEM AND HOME MECHANICS.
PROCESSES TO BE LEARNED.
1. Setting posts.
2. Building fence.
3. Planting trees.
4. Oiling harness.
5. Mending harness.
6. Mending with rivets.
7. Caring for farm and other tools.
8. Pruning trees.
9. Protecting trees.
10. Putting handles in tools.
11. Nailing on horseshoes.
12. Sharpening plows.
13. Mixing mortar.
14. Laying cement walk.
15. Laying stone wall.
16. Hanging doors.
17. Setting locks.
18. Mixing paint and glazing.
19. Building roads.
20. Putting culverts in roads.
21. Gluing.
22. Soldering.
23. Harnessing, hitching, and unhitching
horses.
LISTS OF TOOLS.
WOODWORKING TOOLS.
Two-foot rule.
Auger bits.
Carpenter's steel square.
Brace.
Try-square.
Spokeshave.
T-bevel.
Screw-driver.
Dividers.
Gimlet bits.
Claw hammer.
Countersink.
Plane.
Oilstone.
Marking gauge.
Oil can.
Ripsaw.
Vise.
Crosscut saw.
Bench stop.
Chisel.
Bench hook.
Drawknife.
Miter box.
Mallet.
Carpenter's horse
Mortise gauge.
Gluepot.
mason's
TOOLS.
Crowbar.
Pitching chiseL
Edger.
Stone ax.
Groover.
Trowel, mason's.
Mallet.
Trowel, plastering
Mason's brush.
Trowel, pointing.
Point.
Ladder (to be ma
PAINTER S TOOLS.
Oval brush, No. 8.
Varnish brush, 2-inch.
Varnish brush, 3-inch.
Wall brush, No. 6.
Glass cutter.
Putty knife.
Sash tool. No. 2.
BLACKSMITH S TOOLS.
Shoeing hammer.
Pincers.
Trimming knife.
64633°— 11-
Ball peen hammer.
Cross peen hammer.
Horse rasp.
10 FARM AND HOME MECHANICS.
COST OF EQUIPMENT FOR WOODWORKING CLASSES.
Cost of individual equipment.
1 work bench, as per accompanying drawings $32. 95
1 vise, rapid action, W. C. Toles & Co., Chicago (or equal). No. 55 7. 50
1 plane, jack, Stanley (or equal), Bedrock, No. 604 2. 00
1 plane, block, Stanley, Knucklejoint, No. 18 .85
1 spoke shave, double cutter, 1 J inch, hollow and straight, No. 60 .50
1 draw knife. White's (or equal), No. 31, 8 inch 1. 00
1 chisel, socket firmer. Buck Bros, (or equal), No. 35, I inch .40
1 chisel, socket firmer, Buck Bros, (or equal), No. 35, | inch .45
1 chisel, socket firmer, Buck Bros, (or equal). No. 35, 1^ inch .65
1 gouge, socket firmer, Buck Bros, (or equal), No. 42, outside bevel, regular
sweep .55
1 bit auger. Genuine Russell Jennings (or equal), double spur, I inch .30
1 bit auger, Genuine Russell Jennings (or equal), double spur, ^ inch .45
1 bit drill, twist, Syracuse (or equal), ^ inch .12
1 brace, Stanley (or equal), 10-inch sweep, ratchet, Sampson jaw 1. 75
1 screw driver, Champion (or equal), 8 inch ' .40
1 square, carpenter's, polished steel, No. 100 1. 50
1 square, try, rosewood stock, brass-faced, steel blade, 8 inch .40
1 sliding T-bevel, rosewood stock, brass-faced, 10 inch .45
1 gauge, marking, boxwood, brass thumbscrew, shoe, and face, No. 165 .45
1 rule, Stanley (or equal), boxwood, double brass bound, 1 inch wide, 4 fold . . 35
1 scraper, cabinet, steel, 3 by 5 inch .14
1 pair dividers, wing, 10 inch .30
1 hand screw, beechwood, 12 inch — If by If inch .60
1 saw, hand, rip, H. Disston & Sons (or equal). No. 12, 7 points, 26 inch 2. 25
1 saw, hand, crosscut, H. Disston & Sons (or equal). No. 12, 10 points, 24 inch . 2. 00
1 saw back, H. Disston & Sons (or equal). No. 12, 14 points 1. 25
1 hammer, nail, Hammond's (or equal), adz eye, bell pole, No. 11^ .70
1 mallet, round, hickory, No. 4 .15
1 file, cabinet, open cut, J round, 10 inch .30
1 duster, bench, 10-inch block .60
Total 61.31
Cost of class tools for advanced work.
1 plane, smooth, Stanley (or equal), Bedrock, No. 604, 9 inch $2. 00
1 plane, jointer, Stanley (or equal). Bedrock, No. 607, 22 inch 2.60
1 plane, rabbet and fillister, Stanley (or equal), No. 78 1. 10
1 plane, plow, Stanley (or equal), Universal, No. 55 12. 00
1 scraper, veneer, Stanley (or equal), Adjustable, 3-inch cutter, No. 12 1. 90
1 ax, hand, 4-inch cut .90
1 set chisels, | inch to 2 inch, inclusive, 12 chisels. Buck Bros, (or equal),
socket firmer. No. 35, leather tip handles 5. 90
1 stone, oil, 1 by 2 by 8 inch, Arkansas unmounted (or equal) 1. 00
1 stone, oil, 6-inch slip .30
1 set bits, auger, Genuine Russell Jennings (or equal), x% inch to |f inch,
inclusive, 13 bits, double spur 4. 75
1 bit, expansive, Steers (or equal), No. 1, 2 cutters, | to 3 inch 1. 75
2 countersinks, rose pattern, for wood, at 14 cents each .28
2 nail sets, Starretts (or equal), knurled, medium, at 12 cents each .24
FARM AND HOME MECHANICS. 11
2 Bcrew driver bits for brace, round blade, at 15 cents each $0. 30
1 gauge, mortise, rosewood, plated head, improved screw slide .65
1 can, oil, straight spout, copperized steel, 1 pint .25
1 burnisher, apple handle, 4-inch blade .45
1 saw. frame, turning, 18 inch 1. 00
1 saw, compass, H. Disston & Sons (or equal), 16 inch .45
1 saw set, Tainter's (or equal), positive .75
1 saw clamp, japanned, 9-inch jaws. No. 3 .60
1 glue pot, double, enameled inside, 4 pint 1. 40
Ifile, mill, 10 inch 25
6 files, saw, slim taper, 4^ inch, at 12^ cents each .75
Total 41.75
Total cost 102. 86
SPLIT-LOG DRAG.
(See fig. 26.)
Materials. — A dry log, 7 or 8 feet long and 10 or 12 inches in diame-
ter; 3 sticks, 3 feet long and 3 inches in diameter; a piece of 2 by 4,
3 feet long; a light chain; 3 boards, 8 feet long, 8 inches wide.
Directions. — Split the log carefully down the middle. If one side
should be better than the other, use the better side for the front.
Bore a 2-inch hole in the front log, 4 inches from the end that
will follow the middle of the road; another hole 22 inches from the
opposite end of the log, and one halfway between these two.
In the back log bore a 2-inch hole 20 inches from the end of the
log that is to be in the middle of the road; another 6 inches from the
opposite end, and a third midway between these, being very careful
that all holes are bored plumb.
The logs are to be held apart by stakes tapered at both ends and
driven firmly into the holes and held there by wedges. The logs
should be about 30 inches apart.
Set the 2 by 4 for a brace at the ditch end of the drag, from the
cross stake in the back log to the end of the front log, about an inch
from the bottom.
A strip of iron 3h feet long, 4 inches wide, and J inch thick may
be used as a blade and bolted to the ditch end of the front log, using
bolts with flat heads and the holes for thsm countersunk. This
blade is not necessary, but adds much to the effectiveness of the
drag.
A platform of boards cleated together, leaving spaces of at least
an inch between them, should be placed on the stakes.
" HOW TO USE A DRAG.
Hitch the team so that the earth will move freely along the faces
of the logs when the drag is in motion.
12 FAEM AND HOME MECHANICS.
1. SETTING POSTS.
Posts should be set 2h feet in the ground and tamped sohdly into
place. For barbed wire fences they should be 16i feet apart. For
inclosing large fields or pastures the}' are frequently set at twice
that distance. For board or rail fences the distances betweeen posts
is controlled bv the length of material used, but should never exceed
8 feet. Always set posts in a straight Hne and when practicable
conforming to the cardinal points of the compass. Comer posts
should be larger and longer than other posts and should be set 3^
or 4 feet in the ground and braced from two sides. Posts in low
places should be set at least 3 feet in the ground.
2. BUTLDIXG FENCE.
Cedar posts should always be used when obtainable. Posts of
other material should be treated with creosote or coal tar or should
be charred before being set. In building barbed \vire fences the wire
should be stretched very tight, using a wagon for the stretching. A
wire stretcher does very well for small fields, but is not so satisfactory
for large ones. If the fence is of boards, they should be nailed to
the posts with three nails in each post. Care should be taken to
have boards or wires equal distances apart.
3. PLANTING TREES.
The land where the trees are to be planted should first be carefully
plowed and leveled as for any other crop. The hole for the tree
should be dug wide and deep. The harder the soil the larger the
hole should be, because in such case the tree must start in the loose
dirt that is cut up in the bottom or thrown into the hole. In a loose,
deep soil the hole need not be larger than the spread of the roots.
Trees should be set an inch or two deeper than they stood before
transplanting. The roots that are broken should be trimmed off
at the ends and should be spread out in planting to their normal
position. If there are extra long roots, they should be cut back to
correspond to the rest. The soil must be put in firmly about the
roots, especially under the fork, so that there may be no air spaces
left. This can best be done with the fingers, moving the tree up
and down a little at the same time. The earth should be stamped
down once or t'W'ice as the hole is being filled. The hole should be a
httle more than fuU of earth, so that the surface water can be carried
off, being specially careful not to leave holes near the tree vshere
the water will settle. Stamp the earth thoroughly before leaving
it, to hold the moisture and enable the tree to stand up against the
winds.
A good plan to conserve moisture in planting a tree is to put a
mulch of straw or manure around it.
FAEM AND HOME MECHANICS. 13
The top of the tree should be shortened at the time of plantmg a
little more than the root has been cut off, but should not be trimmed
back too closely.
Plant all orchard trees in straight rows, but ornamental shade
trees should be set out with the general plan of the groimds they are
to ornament in mind, and usually should not be in such rows.
4, 5. 6. OILING AND MENDING HARNESS.
Before a harness is oiled it should be thoroughly cleaned of ail for-
eign substance by scraping off accumulated dirt with a didl knife
and then by washing with castile soap or regular harness soap. It
should then be hung up to dry, but not in the sunlight. When it is
thoroughly dry, it shoidd be inspected to find where it needs mend-
ing. Every break ami every place that shows any sign of giving
way shoidd be repaired. Wlien the re])airing is in the line of sewing,
this should be done with a waxeti thread, but when this is impossible,
mending may be done by using copper rivets, which are readUy
obtainable at every general or hardware store. In using these rivets,
care shoidd be taken to punch in the leather as large a hole as may
be necessary to receive the rivet, and no larger.
After the mending has been done, the harness shoidd be gone
over thoroughly with good harness oil, care being taken not to apply
more than the leather will readily absorb. The harness should then
be hung to dry in the shade, and, after the oil has disappeared,
should be gone over with a cloth. In hot climates a harness soap
is better than an oil.
7. CARING FOR FARM AND OTHER TOOLS.
Tools should be thoroughly cleaned after using ami should be
kept oiled. This is especially true when a tool like a plow is put
away and left for some time without use. Unless it is thoroughly
oiled it will be sure to rust. All steel tools are better for a coat of
oil, but this is essential to every bright tool with a cutting edge.
All edge tools should be kept sharp. Stopping work to sharpen a
dull tool is nearly always economy. Almost the fii"st thing a boy
should learn in the handling of etlge tools is how to keep them sharp
and in good condition for work.
8. PRUNING.
Pruning is removing certain parts of plants or trees to make them
better and more productive, or to keep them in manageable shape
and to make them easier to care for.
A fruit tree should be pruned moderately every year, while an
ornamental tree should be pruned as often as is necessary to remove
dead or superfluous branches and to keep it within the limit ilesigned
for it.
14 FARM AND HOME MECHANICS.
9. PROTECTING TREES.
Trees may be protected from vermin by putting around the lower
part of the trunk of the tree a wire screen or by wrapping with tar
paper. If such protection is used the trees must be watched care-
fully to see that these protections do not harbor other enemies of
the trees.
Insect enemies are destroyed by killing them directly by some
poisonous application or by poisoning their food. For the fungus
enemies of trees some application must be made that will destroy
the fungus.
Applications for both insects and fungus are usually made in water
and sprayed onto the trees. This spraying must be done with
materials which will kill the enemy without injuring the plant or the
fruit, and the work must be thoroughly done before either pest has
obtained a foothold. It is best to spray fruit trees every season
whether a pest has appeared or not.
10. PUTTING HANDLES IN TOOLS.
In all tools having eyes, such as hammers, hatchets, axes, grub
hoes, or picks, the handle should be fitted neatly to the eye, it being
larger at the lower or outer end. The handle is usually larger than
the eye of the tool for which it is intended and should be shaped
down until it fits as close as possible. The handle should be driven
in and split lengthwise of the eye and a wedge driven in tight and
cut off close to the handle; then other wedges should be driven in
crosswise, after which the handle should be dressed off flush with
the tool.
In putting handles into shovels, hayforks, and all tools having
sockets, all the old wood should be removed, rivets taken out and
the handle fitted to the socket as neatly as possible. Then drive it
in tight and replace the rivets. Care must be taken not to drive the
handle too tight as there is danger of splitting the ferrule.
In all tools having a piece of steel inserted in the wood to hold the
handle in place, a hole should be bored in the end of the handle about
Y^ inch smaller than the part that is to be inserted. A ferrule is then
put onto the end of the handle and the handle is driven tightly onto
the tool.
11. NAILING ON HORSESHOES.
It is not expected that every boy shall become an expert horse-
shoer, for horseshoeing is a trade that ought to have several years
of apprenticeship. It is necessary, however, that every boy who
lives on a farm should know how to nail on a shoe that has acci-
dentally been pulled off. This usually comes from the horse's
overreaching, and, if the hoof be not broken, the shoe can be nailed
on without much difficulty.
FARM AND HOME MECHANICS. 15
Be sure that the shoe is placed straight on the foot; then start the
driving with one of the front nails. As small a nail should be used
as will hold the shoe. Drive the nail so that it will follow the wall
of the hoof, coming out through the wall with sufficient length to
twist off and clinch. In clinching the nails, do not strike hard
blows, but rather a number of easy ones, so that the horse's foot
may not be hurt. Do not use a rasp. Always be sure that the
nail comes out through the wall of the hoof.
12. SHARPENING PLOWS.
Heat the plowshare to a cherry red; then hammer it out on the
underside to a sharp edge and in an even line. It should then be
trued up with the hammer and filed on the top side to a sharp bevel
edge. After it is sharpened it should be heated to a dull red and
then held in water until cool.
13. MIXING MORTAR.
In making common lime mortar the first care is the selection
of the lime, which should be free from cinders, clinkers, and other
impurities, and should be chiefly in hard lumps. It should slake
freely in water, forming a fine smooth paste and should dissolve
entirely in soft water when this is added in sufficient quantity.
When prepared for use lime should be slaked in a box and screened
into a pit made for the purpose. The slaking should be done some
days before the lime is to be used in order that it may be complete.
After being screened into the pit it may be covered with sand to
keep out the air, and the preparation will keep almost indefinitely.
It can be taken from this pit at any time and mixed with the required
amount of sand, according to the purpose for which the mortar is
to be used. From 2J to 3 parts of sand to 1 part of lime paste is
the most common proportion.
14. LAYING CEMENT WALKS.
The use of Portland cement in concrete construction has become
so common that its use for ordinary purposes should be known to
everyone, and knowledge of handling it is a resource that every
Indian boy should possess before he leaves school. The funda-
mental principles of the use of cement in making mortar or concrete
are very simple and easily learned. Skill in* its use comes only
from practice and experience.
Cement mortar for brick or stone work is made in the following
proportion: One barrel (380 pounds net) Portland cement, 4 barrels
sand, and 2 pails of lime putty.
Concrete is best made from a mixture of broken stone, clean
coarse sand, and Portland cement, in such proportion that the
16 FARM AND HOME MECHANICS.
cement will just a little more than fill the voids between the grains
of sand.
The coarse material that is used in making concrete is frequently
called the aggregate, and any hard broken stone is suited to this
purpose. Gravel is frequently used, but is not as satisfactory as
the broken stone because of its roundness and smoothness.
In making all concrete mixtures all parts should be carefully
measured. Careful measurement is absolutely necessary to success.
A wheelbarrow makes a very convenient measure.
The concrete should be mixed as near the place where it will be
used as is practicable, so that no time will be lost in getting it into
place. For small jobs only a small quantity should be mixed at
one time, as concrete can not be used after it begins to harden.
Mixing is best done as follows: Measure the sand and spread it
to an even depth on a water-tight platform; measure the cement
and spread it on the top of the sand and then mix thoroughly until
the mixture shows a uniform color; then the measure of stone,
thoroughly wet, should be placed on top and mixed with the sand
and cement in similar manner; then sufficient water should be
added to make a mixture just too soft to bear a man's weight when
it is put in place. Add the water very carefully so that the mixture
shall not be too thin.
Mixtures are medium, ordinary, and lean, according to the amount
of cement contained in each, which is governed by the purpose for
which the mixture is to be used.
A rich mixture for tanks and other water-tight work consists of
1 part cement, 2 parts sand, and 4 parts broken stone. A medium
mixture for foundations, floors, sidewalks, or sewers contain 1 part
cement, 2^ parts sand, and 5 parts broken stone. For heavy walls,
piers, or abutments, an ordinary mixture of 1 part cement, 3 parts
sand, and 6 parts broken stone is used. For large foundations or
other work where the concrete is subjected to continuous plan
strain, a lean mixture consisting of 1 part cement, 4 parts sand, and 8
parts broken stone is satisfactory.
Excavate to the grade decided upon and about 3 inches wider
than the proposed walk and fill v/ith foundation material of broken
stone or cinders to within 4 inches of the proposed finished surface,
wetting the foundation well and tamping it in so that it will be
even and firm but porous. If the soil is good and firm, the founda-
tion may be dispensed with, merely spreading a layer of about
1 inch of sand over the bottom of the excavation, which would
then not be more than 5 inches.
After the foundation has been laid, place 2 by 4's, toenailing
the 2 by 4's to the stakes. Care should be taken that the scantling
be set in straight lines and that these lines be kept the same distance
FARM AND HOME MECHANICS. 17
apart. Fill the frame with concrete, the mixture being 1 part
cement, 2 parts clean, coarse sand, and 4 to 6 parts broken stone,
which should be tamped in until the water begins to show on top.
The finishing coat should be 1 inch thick and of 1 part cement to
Ih or 2 parts good, clean, coarse sand. This should be spread before
the concrete base has set and should be smoothed off with a straight-
edge, flush with the surface of the scantling frames. Smooth with a
wooden plate and cut into square blocks with groover. In warm
climates where the concrete is likely to expand, a seven-eighths-inch
board should be set in across the walk about every 50 or 60 feet to the
depth of the frame. Fill into this, and before the concrete has firmly
set, but when it wall stand, the board should be renioved and the space
filled with dry sand.
Cover the completed walk with sand or other convenient material
to keep it from drying too rapidly and to protect it from dust and the
sun.
15. LAYING STONE WALL.
No wall should be less than 18 inches thick. The largest stones
should be in the foundation course, and as many stones as possible
that go through the wall should be used. Fragments of stones may
be used for filling in.
No joint between two stones should come over a joint between
other two stones, but the stone should overlap from 1 to IJ times the
depth of the course.
Stones should be laid in the wall as the}^ lay in the c^uarry.
All dry and coarse stones should be moistened before they are laid in
order that the stone may not absorb the moisture in the mortar, and
thus dry it too fast. Every part of the joint of all the spaces between
the stones should be filled with mortar, but these spaces should be
made as small as possible. After the mixture is laid the joints in the
face should be cleaned out and refilled with cement mortar. The
joints should be thoroughly cleaned to the depth of at least half an
inch, but an inch is much better. A mixture of 1 part cement, 1 of
sand is, perhaps, most commonly used.
16. HANGING DOORS.
The door is held up against the jambs and marked around with a
pencil. It should then be cut to these lines, being made about one-
eighth inch narrower and three-eighths inch shorter than the open-
ing. The upper hinge should be about 6 inches from the top and the
lower one about 10 inches from the floor. The thickness of the
plinth or the casing should be subtracted from the total width of the
hinge, and the balance divided by two will give the distance the hinge
is to be set back from the face side of the door. In all cases the hinge
64633°— 11 3
18 FARM AND HOME MECHANICS.
should be wide enough to reach across two-thirds of the thickness of
the door. The jamb shoukl be at least 1^ inches thick or else be
backed up solidly, so as to give the hinge screws a good hold; IJ-inch
screws should be used for common size doors. Heavy doors should
have three hinges. The mortise for the hinge of the door should
bevel slightly toward the front, so that the hinge will not strike the
iamb.
17. SETTING LOCKS.
Rim locks are those that are simply screwed onto the face of the
door, while mortise locks are those that are set into the door itself. In
setting the former, the lock is held in position and marked for the
keyhole, knob-bar hole, and screw holes. The first two are cut and
the last are bored, and the lock screwed into place. The escutcheon
and knob plates are put on, and the keeper is then put onto the jamb.
For a mortise lock, the lock is set in the door with a mortise just large
enough to admit it, the face plate of the lock being set flush with the
face of the edge of the door. The places for the holes for the knob
bar and keyhole should then be marked and cut, the lock set and fas-
tened in, the knob-plates and escutcheon set, and the knobs adjusted.
The keeper is then mortised into its proper place flush with the face of
the edge of the jamb.
18. PAINTING AND GLAZING.
Composition of paints: Paint is composed of two ingredients, the
pigment, which gives body and color, and the fluid in which this color
is dissolved or suspended. If the painting is for protective purposes,
the fluid is oil; if for decoration only, it may be water.
The best white pigment is pure white lead, while the most common
black pigment is lamp black. Pigments that will give the different
colors and shades of color may be used as desired.
The oil most commonly used by painters is linseed oil, the drying
qualities of which are improved by boiling, when it is commonly
known as boiled oil. Its quality can be determined by looking
through a small bottle filled with it. Good, fresh oil should be clear in
appearance and have very little odor; poor oil is not clear and has a
strong and rancid odor. If paint is too thick, good oil should be used
to thin it. Driers are frequently used in order to cause the paint to dry
more readily ; in fact, some colors will not dry at all without their use.
A varnish is a solution of a gum or resin in turpentine, linseed oil,
or some like fluid, and is used to produce a hard and shining surface.
A cheap varnish suitable for ordinary work can be made as follows:
Add 2^ pints of turpentine to 3 pounds of dried resin, shake well and
allow to stand for a day or two, shaking occasionally. Add 5 quarts
of boiled oil; shake thoroughly and allow to stand in a warm room
until clear; then pour off the clear ])ortion and it is ready for use.
FAEM AND HOME MECHANICS. 19
Before beginning to paiat, the surface to be painted should be
thoroughly cleaned, and all spots and dust removed. The knots
should be covered with shellac, which can be easily obtained, and all
nail holes, bad joints, and cracks should be filled with putty.
New woodwork should receive at least three coats of paint. The
first coat is called the priming and should be thin and readily ab-
sorbed into the wood. The stopping up of the nail holes, etc.,
should be done after the priming is applied.
The intermediate coats should then be applied as evenly as pos-
sible, the second coat being laid at right angles to the grain of the
wood, while the third coat should follow the grain, care being taken
to leave no brush marks. The final coat should give the desired
tmt.
In repainting old work, it should be carefully cleaned with a knife
and then gone over with powdered pumice stone and water, rub-
bing the greasy parts with lime.
Whitewash is used for common walls and ceilings where, for sani-
taiy reasons, a frequent application is better than a coat which would
last longer. It is made from pure white lime, mixed with water
and is improved by adding a pound of pure tallow to every bushel
of lime. Lime for whitewash should be slaked with boiling water
and, when slaking is complete, the lime can be dissolved in water
and applied with a common whitewash brush. Whitewash is im-
proved by adding 2 pounds of zinc sulphate and 1 pound of common
salt to every half bushel of lime used.
Whitewash can be tinted to any color desired by the use of tints,
which are readily procured.
In setting a pane of glass to replace a broken one, care should be
taken to remove all pieces of the old putty, which can be done with
a knife or with a hot iron. When the glass has been fitted, a thin
layer of putty should be put on the frame and the pane of glass
pressed into place against this. This prevents the glass from touching
the wood and renders it less likely to be broken. The putty should
then be applied smoothly with a putty knife. Glazier's points
should be used to hold the glass in place until the putty is applied.
Putty can be made from whiting and linseed oil, but can be more
readily bought already prepared.
4
19, 20. BUILDING ROADS.
The first and most essential feature in road building is to secure
good drainage, since water is the agent which does most damage.
The road should be shaped like a roof, with the highest part in the
middle and slopping evenly in both directions. On a hill side this
may not be possible and the road will have to have only one slope,
but generally speaking, a roof-shaped road is entirely practicable.
20 FAEM AND HOME MECHANICS.
There are many kinds of road machines in use, all of which are
more or less expensive, but the simplest apparatus for building and
keeping a dirt road is good condition is the split-log dray (figure 33).
This simple implement can be used very easily and effectively and
can be made and owned by any farmer.
Wherever a draw or ditch crosses a road, a culvert of some sort must
be put in. This may be made of stone, if such material is available,
but is most commonly a plain box, made of planks. The size of this
culvert is regulated entirely by the volume of water that is likely to
pass through it durmg a rain storm. It should be set into the road so
that its bottom will be on a level with the bottom of the ditch or drain
that crosses the road, and the road above it should be kept fully up
to grade.
21. GLUING.
Surfaces to be glued should be forced as closely as possible together
and as little glue as possible should be used. The less the better.
Glue should be applied hot and it is also well to warm the joint when
practicable.
Good glue may be known by the way it breaks under the hammer.
The more ragged the fracture the better the glue. The best method
of makmg glue is to fill the umer vessel with small pieces of glue,
cover them with water, and allow them to soak for a few hours. Glue
should be applied hot and so thin that it will run off the brush almost
like linseed oil.
22. SOLDERING.
Soldering is uniting two pieces of metal by means of another metal.
The parts to be joined should be thorouglily cleaned by scraping or
filing, and a flux must be used with the solder to join the two metals.
This flux may be borax or resin, but muriatic acid is commonly used
and is easy to handle. Resin is the best flux for tin; muriatic acid for
zinc and galvanized iron; borax for iron and steel. The acid is kept
in a small bottle with a piece of iron wire through the cork, dipping
into the fluid, so that a drop may be applied to the surface of the
metal to be soldered when desired.
The soldering iron must be kept tinned or it will not spread the
solder. A few small scraps of tm are mixed with some resm in a hol-
low place in a brick or some similar place, and the hot iron is rubbed
into tliis mixture until the tin has melted and adhered to the iron
through the agency of the resin. A good-sized iron should always be
used.
When the surfaces to be brought together are prepared, the solder-
ing iron should be heated to a dull red and should then be rubbed
clean on a piece of rag and applied to the solder in such a way that
FARM AND HOME MECHANICS. 21
the melted solder will cover the place to be mended. The solder
should be then rubbed smooth from the jomt with the iron, care bemg
taken that it be not too hot.
23. HARNESSING, HITCHING, AND UNHITCHING
HORSES.
Always handle 3"our horses gently. Always speak to them before
you go into the stall. Do not throw the harness on them as they do
not enjoy being hurt. Always be sure that all buckles are fastened
and that the ends of the straps are put mto the keepers. In hitchmg
a horse or a team to a vehicle, the traces should be the last thmgs
fastened, the Imes being taken down first, so that the animals are
always under control.
In unhitching, exactly the reverse process is followed, the lines being
the last part of the harness to be put up.
In unharnessing a team, the buckles should always be loosened on
the left-hand side.
22
FAKM AND HOME MECHANICS.
le
J*.
Fig. 1. — Bread Boakd.
FAEM AND HOME MECHANICS.
23
^l^'x *^po6fr
<r/cor. a "rou
Fig. 2.— Stall, Feed Box, and Manger.
BILL OF material.
2 pieces yellow pine 4" x 4" x 10' 0".
2 pieces yellow pine 2" x 4" x 10' 0".
1 piece yellow pine 2" x 4" x 12' 0".
1 piece yellow pine 2" x 4" x 0' 0".
4i pieces yellow pine 1" x 10" x 12' 0".
IG pieces yellow pine 1" x 10" x 10' 0".
1 piece yellow pine 1" x G" x 12' 0".
1 piece yellow pine 2" x 12" x 10' 0".
Z\ pieces yellow pine 1" x 9" x 12' 0".
1 piece yellow pine 2" x 8" x 5' 0".
24
FARM AND HOME MECHANICS.
w
1 ^
k-
/6
T
■^
i
90
-/y
Fig. 3.— Hen's Nest.
FAEM AND HOME MECHANICS.
25
Fig. 4.— Henroost.
64633°— 11 4
26
FARM AXD HOME MECHANICS.
Fig. 5— Gate.
bill of materla.l.
5 pieces yellow pine 1" x 6" x 10' 0*
C pieces yellow pine 1" x 6" x 4' 6".
2 pieces "yellow pine 1" x 6" x 7' 0".
FARM A2S1D HOME MECHANICS.
27
Ffoni £'(ei^aiion
■Sedion
Fig. 6.— Chicken Coop.
bill of material.
4 pieces yellow pine 1" x 10" x 3' 6" Top.
2 pieces yellow pine 1" x 10" x 4' o" Bottom.
1 piece yellow pine 1" x 10" x 15" Door.
1 piece yellow pine I" x 10" x 12' 0" Front and back.
28
FARM AND HOME MECHANICS.
\-
u° 11 A-
10
— 4-
Oo
^ jL
1.,
Fig. ".—Milk Stool.
BILL OF MATERIAL.
1 piece yellow pine IJ" x 8" x 10".
1 piece yellow pine 2" x 4" x 10"-.
Top.
Leg.
/«
i ■
-4»-4'^3*
'l! o I
O'
%
^ —
7^-
.^-O-
nm
Fig 8.— Eveneb.
FARM AND HOME MECHANICS.
29
>^
^
— ,
1
^ , • 1
i
^ —
1
^-6:
U
.^-o
Fig. 9.— Feed Trough.
bili of material.
2 pieces yellow pine li" x 10" x 4' 6" Sides.
2 pieces yellow pine U" x 8" x 2' 0" Ends.
2 pieces yellow pine 1" x 2" x 12" Crosspieces.
30
TARM AND HOME MECHANICS.
TT
S'O
i
i
hf*
/'/<C-^
in
Fig. 10.— Water Trough.
bill of material.
3 pieces yellow pine \\" x 13" x 5' 0" Sides and bottom.
2 pieces yellow pine U" x 12" x 1 ' 10" Ends.
2 pieces yellow pine 2" x 4" x 4' 6" Crosspieces.
6 pieces yellow pine 2" x 4" x 1 ' 0" Legs and braces.
FARM AND HOME MECHANICS.
31
f?!^
r-
fcM
I
^' 0^
I
Fig. 11.— Wall Shelf,
bill of material.
1 piece yellow pine 1" x 11" x 4' 2".
2 pieces yellow pine 1" x 9" x 11".
32
FARM AND HOME MECHANICS.
Its^
M
-4'-o^-
kf-i
Fig. 12.— Hanging Shelf,
bill of material.
1 piece yellow pine 1" x 12" x 4' 4".
2 pieces yellow pine 1" x 12" x 3' 0"
2 pieces yellow pine 1" x 3" x 12*.
FARM AND HOME MECHANICS.
33
Fig. 13.— Footstool,
bill of material.
1 piece yellow pine 1" x 10" x 12 J" Top.
2 pieces yellow pine 1" x 10" x 9" Ends.
1 piece yellow pine 1" x 2" x 14" Crosspiece.
34
TAKM AND HOME MECHANICS.
Fig. 14.— Flour Box.
bill of material.
t pieces yeiiow pme
8 pieces yellow pine
FARM AND HOME MECHANICS.
35
. , .... .. . ,
^-ir
I rr :r- JUT jzr rr ■=. r= ^ 31 ^.-n-^
X
"^j,^>
K-
Zi
:i^*- Ti'P^"""^
■4-^ <y>
Fig. 15.— Bench.
bill of material.
2 pieces yellow pine 1" x 12" x 0' 2"
4 pieces yellow pine 1" x 10" x 1' 6"
2 pieces yellow pine 1" x 4J" x 6' 0"
36
FARM AND HOME MECHANIC&.
Fig. IC— Knife Box.
BILL OF MATERI.\L.
1 piece yellow pine i" x 8" x 13" Bottom.
2 pieces yellow pine h" x 3" x 13" Sides.
2 pieces yellow pine |" x 3" x 10" Ends.
1 piece yellow pine f " x 6^" x 12" Partition.
FARM AND HOME MECHANICS.
37
c-o
1.
J'O
rjw
Fig. 17.— Table.
BILL OF MATERIAL.
4 pieces yellow pine 1" x 10" .x 6' 0" Top.
4 pieces yellow pine 4" x 4" x 2' (i" Legs.
3 pieces yellow piae 1" x 6J" x 6' 0" . . .... Side and end pieces.
38
FARM AND HOME MECHANICS.
,^
petlil A.
Fig. 18.— Cupboard-
bill OF MATERIAL.
4 pieces yellow pine 1" x 10" x 5' 6" Doors.
4 pieces yellow pine 1" x 3i" x 16" Cleats on doors.
4 pieces yellow pine 1" x 8" x 6' 0" Sides.
2 pieces yellow pine 1" x 10" x 4' 0" Top.
2 pieces yellow pine 1" x 8" x 3' 6" Bottom.
1 piece yellow pine 1" x 6.^" x 10' 6" Base.
2 pieces yellow pine 1" x 3" x 6' 10" Front stiles.
2 pieces yellow pine 1' x 2" x 8' 6" Front rails.
5 pieces yellow pine 1" x 10" x 6' 0" Back and shelf supports.
8 pieces yellow pine 1" x 8' x 3' 0" Shelves.
2 pair hinges.
1 cupboard catch.
FARM AND HOME MECHANICS.
39
^■1^
i9"-
-^l
-zz
J
1
3"-43l
Fig. 19.— Towel Roller,
bill of material.
1 piece yellow pine 1" x 6" x 2' 0" Back
2 pieces yellow pine 1" x 4" x 3.^" Bracket.
1 piece yellow pine 2" x 2" x 2' 0" Roller.
40
FARM AND HOME MECHANICS.
e5«t iy-i<**
iTTf ^ IT *^ "v
UJIU
—3-6-
-^-------
-■^.
d
1^
Fig. 20.— Bedstead,
bill of material.
2 pieces yellow pine 1" x 9" x 3' 8" Head.
1 piece yellow pine 1" x 12" x 3' 8" Foot.
2 pieces yellow pine 1" x 9" x 6' 8" Sides and cleats.
2 pieces yellow pine 2" x 4" x 2' 8" Head posts.
2 pieces yellow pine 2" x 4" x 2' 1" Foot posts.
2 pieces yellow pine 2" x 6" x 3'6" Bottom.
6 pieces yellow pine 1" x 6" x 3' 6" Bed slats.
FARM AND HOME MECHANICS.
41
B>r-i—
r
->^
U— *:
1
i!
;i'-7- ^
Fig. 21.— Window Screen.
bill of material.
2 pieces yellow pine 1|" x 3" x 5' 4" Stiles.
2 pieces yellow pine l|" x 3" x 2' 7" Rails.
1 piece yellow pine IJ" x 3" x 2' 7" Lower rail.
30 feet screen binding \" x |".
42
FARM AND HOME MECHANICS.
^eta'/l of st^ecn^Sm dm^
Fig. 22.— Door Screen.
bill of material.
2 pieces yellow pine \\" x 4" x 7' 2" Stiles.
2 pieces yellow pine \\" x 4" x 2' 8" Rails.
1 piece yellow pine \\" x 5J" x 2' 1" Lower rail.
2 pieces yellow pine IJ" x 4" x 3' 2" Braces.
24 feet screen binding J" x |".
FARM AND HOME MECHANICS.
43
t
T
7
'ir
1 '
«o
Fig. 23.— Bookcase,
bill of materlal.
2 pieces yellow pine 1" x 12" x 5' 2"
6 pieces yellow pine 1" x 12" x 3' 6"
Sides.
Shelves.
44
FARM AND HOME MECHANICS.
Fig. 24.— Tool Chest.
bill of material.
4 pieces yellow pine 1" x 8" x 4' 8" Sides.
4 pieces yellow pine 1" x 8" x 1' 6" Ends.
4 pieces yellow pine 1" x 10" x 4' 8" Top and bottom.
6 pieces yellow pine 1" x 3J" x 4' 10" Base and top strips.
6 pieces yellow pine 1" x 31" x 1' 10" Base and top strips.
1 piece poplar J" x 9" x 7' 0" Tray.
FARM AND HOME MECHANICS.
45
^'.0'
Fig. 25.— Clothes Box.
bill of material.
2 pieces yellow pine 1" x 12" x 4' 2" Sides.
2 pieces yellow pine 1" x 12" x 2' 0" Ends.
6 pieces yellow pine 1" x 9" x 4' 2" Top and bottom.
3 pieces yellow pine 1" x 34" x 4' 4" Base.
2 pieces yellow pine 1" x 2" x 4' 4" Edge of top.
46
FARM AND HOME MECHANICiS.
Perspective view.
Plan and elevation.
Fig. 26.— Split-Log Dkag.
FARM AND HOME MECHANICS.
47
1/1=
%.^.-.
^^?
U\J
III
r— Tf
Oe49tl-
Fig. 27.— Hayrack.
BILL OF MATERIAL.
2 pieces yellow pine 2" x 10" x 16' 0"
4 pieces yellow pine 2" x 6" x 8' 0".
4 pieces yellow pine 2" x 4" x 4' 2".
2 pieces yellow pine 2" x 4" x 15' 8".
4 pieces yellow pine 2" x 4" x 4' 0".
1 piece yellow pine 2" x 4" x 6' 2".
4 pieces yellow pine 2" x 4'' x 1' 4".
HARDWARE.
4 pieces yellow pine 2
16 pieces yellow pine 1'
4 pieces yellow pine 1
4 pieces yellow pine 1'
6 pieces yellow pine 1
2 pieces yellow pine 1
1 piece yellow pine 1"
" X 8"
X 5' 8".
" x6'
xl'4".
"x6'
X 11' 0"
" x 6"
x9'0".
" X 6"
X 16' 0"
"x 1(
" X 16' 0
X 10"
X 11' 0"
6 bolts I" X 6".
16 bolts I" X A".
8 Clips, bolt Y X 19".
48
FARM AND HOME MECHANICS.
n-
UL
h la '-
^^
Ut
Fig. 28. — Details of a Cheap Workbench.
0
COOOOS'Or-l^ to O (MOO
as ^ (M
9 to M 05 03 d'5
l^a
Sfl
3 a c3
■ C !r! Sr" i^
'^ » *^ c" '
ft ft So o
5f^M
c3 S o 5S a S •s ci
Q
~ ; , i 03 S
•S-a ^ ^ J, J-g-aj3
■3-2.2.!a.2.S2 a 5 a
CB a5«««<a (c Q) a>
.9.3 §§§§.9 .a .g
ss o o o cs — rs
a- c^::^;=^r^^ a; o^ a.'
'^<i ij " . -J ^ J 'J •< *^ <i
C3 o O » "» "s % * O 00 tb
i^ r-ooeoiNv V V
,„0!; s a t » OOOl
^r-llMCOcOCOCOi-Hi-l
-X 1^ >^ X !^ X X X "
sSSSoooooo oouooooo
a o QJ S Cj O G; a; O 03 ni r^ r^ n. Oi r^ n1 ^-j
^ 'ft'ftft ft'ft'ft ft ft ft
»H W^ -^ ^ CM M M M t^
a a -s a a fl S
■ftp-^ftftftc
lllllllll
^:^^<
J^ ^
X X
ftft
■■oo
e3 ™ =s -j^*"
OT.2 '^•q a ft
a 9 a<d'5o
555i^|z.'a3
^^'^c^g'ag
- - - ^-(M ftQ,M
O) --I ^ , . O <M J3 <5
O"^.'
X<M-
X-
;5 "'(N ' 1J(N
^^^ X^^ X X
as
X
oouoooooo':©
o o o a; ^0^ ^2 .2 .2 .2 2 o
'ft'ft'ft"ft ft'ft'ft a. ftx) ^
a^tJ*
r-llO.^
^» » N X '^^M
aaagai^-ssls
5 — — — Sji'rt ^»o-^
l^ini^I^ — I^'-^ Ko « a
t^OMOOOO"^, o,'?
V a
Si ^-
"3 a
Farm aud Hume Mccbanius,
1-
•*>
P
^
e-o-
T
^
'r~T
15
xzzi:
/^^^..
fe
lll__^i
Details of Maxual Traiiong Workbench.
nd Home Me^'hanics.
Pane/s in back. /S 23% "
Towe/ racks
"TopU he covered witk sheet z/rc
j "PopJar^
/Veil /ron.
Mathod of jasfenma z//vc on. fop-
Plate IV.
HILL OF MATERIAL.
4 pieces, r X 8" X 5' 8", "A" yellow pine Bnish T„„
4 pieces, 4" x 4" x 2' 7". "A" yeUow pine fin sh • '»Ki» i
4 Tiippps 1 v V *i" V T Qw «« A >, „ ,T ^ . ^ iiuisn i able legs.
4 p Icis' ll" X 3" X V %•' "V S °" P^™ '^ish . . End railf
2SiS'u''vii''viMi' .f„5'«",°wP'?e finish Side rails.
-pieces,!, X2J XI 3, A" yeUow pine finish.... Front and back
2 p S' 1" X 8" X 2' ^' •' ^■ Tn "'^ P'oe finish Bacfc-panels.
liieif'n"^%'i\S' ..-^.y^o^P't'e finish Partition
14 n S U" X 3)." X 2^-V ^' A ^'"T P'"? '^'^'^ Brackets.
0 p eces' P X 3" X ?' f>" 'I a '^™?i"*"^-P"!I "°'«'i- • drawer slides.
0 pieces, 1 X3 X2 0', A yellow pine finish Bread board fronts
t fS n'K-'w' X 2"3'-. A-^'"r "'"^ '^"i^" TowefhaTgers.
0 pieces, ij X w x 2 3 , "A" yellow pine finish . Drawer fronts
6 p eces, J x 9 x 2' 0", poplar panel . .'^^ nSwIr S
3 pieces, ;/' x 9" x 2' 3", poplar panel DrIwCT Inds'
4 drawer bottoms, i" poplar panel. 18 square feet ' ' '
tj^Sllfo^rfc';^it=,ete: - ^ - Bread boards.
HARDWARE.
1 piece sheet Zinc, 36" X 72" For ton
1 ijiece iron, No. 22, li" x 10' long \rouna'tOD
i> drawer pulls. -vrouna top.
5-6 -
Domestic SciEts Table.
KECAPITtJLATION AND COST OF MATERLIL.
35 feet lumber, 1" x 8" x 12', "A" yellow pine, at *50 per M $1 7.i
3S feel lumber, 1 J" X 10" X 12'. "A" yellow pine, at $50 per M . ..173
15 feet lumber, 4" X 4". "A" yellow pine, at S50 per M.. .. 7.,
4 feet lumber, 2" x 2" x 10', "A'" yellow pine, at $50 per M '. .'2(1
8 feet lumber, l"x 10" X 9', poplar, at $70 per M . S(i
33 feet lumber, i"x6" to 12", poplar panel, at $70 per M 2.31
1 piece sheet zinc, 30" x 72" i so
1 piece iron. No. 22, ll"xl6'long '". iso
8 drawer pulls, at 10 cents each 80
Amount 9. 92
Carpenter labor 10. 75
Cost of construction 20. 67
PAINT MATERIAL.
1 quart white shellac 75
3 pints coach varnish 1.20
Total cost 22.62
ys.
l:/ ■
.^*.
. v^ - V
■r. s
■ »: ■
; rr^
"K
:, -^r: ■
■^^
iMM^
^■:-
^ .
€^'^^^^
• i
A-';- >^0^;^.|M^ "^Jli^:^^
/ \ /^
rvA-)^
^:-^
Live Music Archive
Librivox Free Audio
Metropolitan Museum
Cleveland Museum of Art
Internet Arcade
Console Living Room
Books to Borrow
Open Library
TV News
Understanding 9/11